Dyson SV12 Manual De Instrucciones página 11

EN
DOCKING STATION INSTALLATION
• Unpack the docking station, plug and installation leaflet.
• Select the location for the docking station and ensure that there is no pipework
(gas, water or air), electrical cables, wires or ductwork directly behind the
mounting location.
• Follow the instructions on the Installation leaflet.
• Click the attachments into place.
• Place the machine in the docking station.
• Plug in the docking station and turn on to charge.
• Your machine will need to be fully charged before first use.
Dyson recommends the use of protective clothing, eyewear and materials when
installing the docking station.
VACUUMING
• Remove the machine from the docking station.
• Check that the underside of the cleaner head or tool is clean and free from
foreign objects that may cause damage.
• Your machine has a slider control on the cleaner head to adjust the suction.
Select the suction required:
MAXIMUM SUCTION FOR GROUND IN DUST AND DEBRIS (+)
• For vacuuming durable floor coverings, hard floors and heavily soiled carpets
and rugs.
– Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
– Your machine is pre-set to this level of suction when you take it out of the box.
SUCTION FOR DUST AND DEBRIS ()
• For vacuuming of lightly soiled carpets, rugs and hard flooring.
• For vacuuming of large debris such as peanuts or rice.
– To switch to this setting, move the suction control slider on top of the
cleaner head.
SUCTION FOR DEEP PILE CARPETS AND DELICATE FLOORING (-)
• For vacuuming deep pile carpets or rugs and any flooring on which you may
experience greater resistance.
• For vacuuming of lightly soiled floors, including delicate flooring such as vinyl,
parquet and lino.
– To switch to this setting, move the suction control slider on top of the
cleaner head.
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
The brush bar on the machine can damage certain carpet types and floors.
Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming without the motorized floor tool and
consulting with your flooring manufacturer.
LIGHTS DURING CHARGING
Charging, low charge
Charging, medium charge
Charging, nearly full
Fully charged
LIGHTS DURING USE
High level of charge
Medium level of charge
Low level of charge
Empty, needs charging
LIGHTS DIAGNOSTICS
Battery fault - call Dyson Helpline
Main body fault - call Dyson Helpline
Charger fault - call Dyson Helpline
FILTER AND BLOCKAGE INDICATOR LEDS
Blockage indicator
Filter unit requires washing
Filter unit not fitted correctly
See battery section
EMPTYING THE CLEAR BIN
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure the machine is disconnected from the charger before emptying the clear
bin. Be careful not to pull the "ON" trigger.
• Avoid pulling the "ON" trigger when emptying.
• Remove the wand by pressing the red wand release button and pulling away
from the bin.
• To release the dirt:
– Hold the machine with the bin in a downwards position.
– Firmly push the red bin release button.
– The bin will slide down, cleaning the shroud as it goes.
– The bin base will then open.
– The bin base will not open if the red button is not pushed down fully.
To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
Remove the clear bin carefully from the bag.
Seal the bag tightly, dispose as normal.
CLEANING THE CLEAR BIN (OPTIONAL)
If it is necessary to clean the clear bin:
• Follow the instructions in the "Emptying the clear bin" section.
• Press the red button located on the bin runner to release the bin and slide the
bin off the runner.
• Clean the clear bin with a damp cloth only.
• Ensure that the clear bin and seals are completely dry before replacing.
• To refit the clear bin:
– Insert the spine on to the bin runner.
Close the clear bin by pushing the bin base upwards until the clear bin and bin
base click into place.
The clear bin is not dishwasher safe and the use of detergents, polishes or air
fresheners to clean the clear bin is not recommended as this may damage
your machine.
FILTER AND BLOCKAGE INDICATOR LEDS
Your machine has two indicator lights that will help alert you that simple
maintenance steps are needed.
• The filter indicator will flash intermittently when the filter unit is not fitted
correctly. Follow the instructions on how to refit the filter unit in the 'Washing the
filter unit' section.
• The filter indicator will light continuously when the filter unit needs washing.
Follow the instructions on how to wash the filter unit in the 'Washing the filter
unit' section.
• The blockage Indicator LED will light if there is a blockage. Follow the
instructions on how to clear blockages in the 'Looking for blockages' section.
WASHABLE PARTS
Your machine has washable parts, which require regular cleaning. Follow the
instructions below.
11