Publicidad
Idiomas disponibles
Idiomas disponibles
H-3133U-12, H-3134U-12
π
H-3135U-12, H-3136-12
H-5210-12
8-12 STEP SAFETY ANGLE
ROLLING LADDERS
12" DEEP TOP STEP
TOOLS NEEDED
Step Ladder
Rubber Mallet
A. Side Handrail (1)
B. Side Handrail (1) Opposite
C. Rear Handrail Bar (1)
(shipped taped to the handrail)
(2 for 12 step)
D. Stile (1)
E. Base Panel (1)
WARNING! Assembly of these types of ladders
can be inherently dangerous. Please take all
necessary precautions during the assembly
process. Always use a separate ladder to
finish assembly in high places. Never climb a
ladder that is not completely assembled. Do
not assemble or use a ladder with missing or
damaged parts. Use proper lifting mechanics
when assembling a ladder. Watch for overhead
electrical hazards and obstructions.
PAGE 1 OF 6
1-800-295-5510
uline.com
9/16" Wrench or Socket (2)
7/16" Wrench or Socket
Safety Glasses
PARTS
F. Back Panel (1)
ASSEMBLY
STEP 1: FRAME ASSEMBLY
1.
Place the ladder stile (D) on the floor. Be sure to
assemble on a protective surface so the finish does
not get damaged. (See Figure 1)
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
G. Horizontal Brace (2)
H. Vertical Brace (2)
Notched Bushing (2)
(4 for 12 step and
California OSHA)
Handrail Bracket (4)
(shipped attached to handrail)
(6 for 12 step)
NOTE: DO NOT tighten bolts until instructed to.
NOTE: Back panel (F) has both round and
slotted holes. The round holes are at the bottom,
and the slotted holes are at the top (L1).
Hardware Kit (1)
(misc. hardware
included)
Gray Bushing (4)
(6 for 12 step)
0521 IH-3133U-12
Publicidad
Tabla de contenido
Manuales relacionados para Uline H-3133U-12
Resumen de contenidos para Uline H-3133U-12
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-3133U-12, H-3134U-12 π H-3135U-12, H-3136-12 1-800-295-5510 H-5210-12 uline.com 8-12 STEP SAFETY ANGLE ROLLING LADDERS 12" DEEP TOP STEP TOOLS NEEDED 9/16" Wrench or Socket (2) Step Ladder 7/16" Wrench or Socket...
- Página 2 (4) 1/4-20 x 2¾" hex head cap screws. (See Figure 2, Step 3) NOTE: Do not proceed until ladder is stable. NOTE: You may now tighten all handrail bolts. 1-800-295-5510 PAGE 2 OF 6 0521 IH-3133U-12 uline.com...
-
Página 3: Escaleras De 8-12 Escalones Con Ángulo De Seguridady Ruedas
H-3133U-12, H-3134U-12 π H-3135U-12, H-3136-12 800-295-5510 H-5210-12 uline.mx ESCALERAS DE 8-12 ESCALONES CON ÁNGULO DE SEGURIDAD Y RUEDAS ESCALÓN SUPERIOR DE 12" DE PROFUNDIDAD HERRAMIENTAS NECESARIAS 2 Llaves o Dados de 9/16" Escalera Llave o Dado de 7/16" Mazo de Hule... -
Página 4: Continuación Del Ensamble
4 tornillos de cabeza hexagonal de NOTA: NO proceda hasta que la escalera quede 1/4 -20 x 2¾". (Vea Diagrama 2, Paso 3) estable. NOTA: Ya puede apretar todos los pernos del pasamanos. 800-295-5510 PAGE 4 OF 6 0521 IH-3133U-12 uline.mx... -
Página 5: Outils Requis
H-3133U-12, H-3134U-12 π H-3135U-12, H-3136-12 1-800-295-5510 H-5210-12 uline.com ÉCHELLES SUR ROULETTES À ANGLE SÉCURITAIRE DE 8 À 12 MARCHES MARCHE SUPÉRIEURE DE 12 PO DE PROFONDEUR OUTILS REQUIS Clé ou douille de 9⁄16 po (2) Escabeau Clé ou douille de 7⁄16 po Maillet en Lunettes de sécurité... -
Página 6: De Main Courante Arrière
4. Lorsque les marches sont de niveau, serrez tous les bou- 1/4 -20 x 2 ¾ po. (Voir Figure 2, Étape 3) lons installés. REMARQUE : Vous pouvez maintenant serrer tous les REMARQUE : Ne continuez pas à moins que boulons de main courante. l'échelle soit stable. 1-800-295-5510 PAGE 6 OF 6 0521 IH-3133U-12 uline.ca...