Roger Technology B72/DGS Instrucciones Y Advertencias Para El Instalador página 4

1
General safety precautions
Warning: incorrect installation may cause
severe damage or injury. Read the
instructions carefully before installing the product.
This installation manual is intended for qualified personnel only.
ROGER TECHNOLOGY cannot be held responsible for any damage
or injury due to improper use or any use other the intended usage
indicated in this manual.
Installation, electrical connections and adjustments must be
performed by qualified personnel, in accordance with best
practices and in compliance with applicable regulations. Before
installing the product, make sure it is in perfect condition.
Disconnect the mains electrical power before performing any
work. Only use original spare parts when repairing or replacing
products.
The packaging materials (plastic, polystyrene, etc.) should not be
discarded in the environment or left within reach of children, as
they are a potential source of danger.
WARNING! Handle electronic parts and terminals with extreme
care, as these parts are highly sensitive to static electricity.
2
Product description
The B72/DGS card is a device with the function to eliminate the
residual magnetism caused by the uninterrupted power supply of
the electro lock when the barrier is completely closed, facilitating
the release of the bar when the opening command arrives.
The device is supplied for barriers with integrated control board
CTRL (compatible with firmware P4.10 or later and it must be
used only with BAFS/05).
3
Reports
A RED LED (L1) is mounted on the control board that blinks briefly
when demagnetization is performed.
4
Technical characteristics
Power supply input 30% modulated voltage
(terminals 1,2) Vmax = 40Vdc
Exit - (terminals 3,4) Imax = 280mA
Overload protection thermal, with PTC
NOTE: the activation of the anomaly protection in the current
absorption causes the intervention of the PTC thermal protection;
in this situation the electro lock will not be powered. To restore
correct operation, disconnect the power supply to the control unit
(or alternatively activate the release key that removes power from
the +ES output) and wait 1 minute.
5
Installation
1. Apply the double-sided adhesive tape to the back of the casing
of the B72/DGS board.
2. Fix the casing inside the BOX of the CTRL control unit, on the
ENCODER, LED LIGHT and LOCKS terminal board side.
3. Connect the B72/DGS board as shown in figure 2.
WARNING: If the polarity of the connection to terminals 1 and 2
is reversed, the electro lock will never be powered, preventing the
safety function.
4
6
Setting parameters
The functions of the B72/DGS board are enabled and disabled
with parameter 29 of the CTRL control unit.
29 00
Electroblock type selection
Magnetic "ventouse" type electroblock with dema-
gnetizer B72/DGS
NOTE: In the case of MASTER/SLAVE installation,
03
in order to use the selection par. 29 = 03 it is
necessary that both control units have firmware
P4.10 (or later).
7
Initial testing
The testing must be performed by qualified technical personnel.
The installer is required to measure impact forces and select on
the control unit the appropriate speed and torque values to ensure
that the motorised door or gate remains within the limits defined
by the standards EN 12453 and EN 12445.
1) With the arm closed, check that the electro lock device ensures
locking to the support.
2) Give an opening command and check that the drive is preceded
by the release of the arm by the electro lock (LED L1 blinks briefly).
3) When the barrier closes again, the electro lock is activated
again: now activate the release of the barrier, and check that after
a few seconds the barrier is free to be moved by hand.
4) Lock the mechanics again.
8
Disposal
The product may only be uninstalled by qualified
technical personnel, following suitable procedures for
removing the product correctly and safely. This product
consists of numerous different materials. Some of
these materials may be recycled, while others must be
disposed of correctly at the specific recycling or waste
management facilities indicated by local legislation applicable for
this category of product.
Do not dispose of this product as domestic refuse. Observe local
legislation for differentiated refuse collection, or hand the product
over to the vendor when purchasing an equivalent new product.
Local legislation may envisage severe fines for the incorrect disposal
of this product.
Warning! Some parts of this product may contain substances
that are harmful to the environment or dangerous and which may
cause damage to the environment or health risks if disposed of
incorrectly.
9
Additional information and
contact details
ROGER TECHNOLOGY is the exclusive proprietor holder of all
rights regarding this publication.
ROGER TECHNOLOGY reserves the right to implement any
modifications without prior notification. Copying, scanning or any
alterations to this document are prohibited without express prior
authorised from by ROGER TECHNOLOGY.
ROGER TECHNOLOGY CUSTOMER SERVICE:
business hours: Monday to Friday
08:00 to 12:00 - 13:30 to 17:30
Telephone no: +39 041 5937023
E-mail: service@rogertechnology.it
Skype: service_ rogertechnology