Thomashilfen RECARO Sport HERO Reha Instrucciones De Montaje página 6

Lateral seat support
The RECARO Sport HERO Reha is fitted with a seat reducer. The lateral seat supports are fitted to this seat reducer. To fit them, pull the lateral seat supports over each of
the side sections of the seat reducer. Then hook and loop-fasten the lateral seat supports to the outside of the seat reducer.
The cover can be removed and machine-washed at up to 30°C/86°F.
Fig. 4a: Pulling the lateral seat supports over the seat reducer
Footrest adapter (accessory)
Before assembly, clean the plastic surface on the underside of the seat with commercially available cleaning agents (e.g. water and rinsing agent) until it is completely
free from grease.
Now remove the hook and loop strips (fleece) from the adapter plate and attach them to the underside of the seat. The hook and loop strips (hooks) remain on the adapter
plate.
Position the seat flush in a 90° angle at the front of the adapter (handle of the adapter facing forwards) and tilt the seat over to hook and loop it to the adapter.
Footrest: The footrest is attached to the adapter.
Fig. 5a: Attaching hook and loop straps to the seat
Footrest, short 12 cm / 4.7" (accessory)
Push the footrest tubes into the front of the adapter. To do this, depress the catch springs on the footrest. Always secure the footrest against falling out using the knurled
nuts on the left tube of the footrest adapter. Multiple holes in the footrest tubes allow the footrest to be adjusted to match the depth of the vehicle's seat.
To stabilize the footrest on the vehicle floor adjust the height of the support bars by screwing them in or out until they have contact with the vehicle. Then lock the
support bars with the hand knobs to prevent them unscrewing accidentally. Screw the hand knobs upwards as far as possible and tighten them fast.
Lower leg length:
The lower leg length is adjusted by changing the height of the footrest. Loosen both outer screws. Retighten them after each adjustment.
Foot angle:
Loosen the four screws left and right on the underside of the footrest to adjust the desired foot angle with the rails. Then retighten the screws.
Fig. 6a: Inserting the support
Turning plate with footrest adapter (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Seatfix connection (for turning plate) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Stabilising bow, rear (for turning plate) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Stand, front (for turning plate) (accessory)
Please note our separate instructions for mounting! Download: www.thomashilfen.com
Seat wedge, bottom (accessory)
The seat wedge is positioned centrically below the car seat. The high edge is at the front to achieve an optimum rest position of the child.
The cover can be removed (zipper) and washed in the machine at up to
30° C / 86° F.
Please note:
Function of the turning plate is considerably reduced if being used in combination with the seat wedge. We therefore do not recommend using seat wedge and turning
plate at the same time.
Fig. 7a: Positioning seat on seat wedge
Table (accessory)
Mount the side parts of the table first, by pulling them over the round corners of the seat. The side with the larger fabric must face outwards. Attach the fabric to the
wheels for the seat adjustment using the provided holes in the cover of the side parts. Then tuck the downwards overlaying fabric below the seat cover.
Now fasten the table to the hook and loop straps of the side parts. Guide the belt around the back of the seat and fasten it to the hook and loop (fleece) at the side of the
table.
Note:
For reasons of space the crotch pad should be removed when using the table.
The cover can be removed and washed in the machine at up to 30° C / 86° F.
Fig. 8a: Mounting the side parts
6
RECARO Sport HERO Reha – Instructions for assembly and use (supplement)
Fig. 4b: Hook and loop-fastening
Fig. 5b: Attaching seat to adapter
Fig. 6b: Adjusting height to vehicle
Fig. 7b: Final position
Fig. 8b: Attaching the table
item code: 866
item code: 806 .1
item code: 820
item code: 818
item code: 819
item code: 817
item code: 810
item code: 811