Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (
Original Instructions)
Intended use
Your STANLEY STHM10 Demolition Hammer has been
designed for heavy duty demolition, chipping and chiseling
applications in concrete, brick, stone and other masonry
materials.
SAFETY INSTRUCTIONS
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference. The term "power tool" in the warnings refers
to your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1. Work area safety
a.
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c.
Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2. Electrical safety
a.
Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
b.
Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d.
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
e.
When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f.
If operating a power tool in a damp location
16
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock. NOTE: The term "residual
current device (RCD)" may be replaced by the term
"ground fault circuit interrupter (GFCI)" or "earth
leakage circuit breaker (ELCB)".
3. Personal safety
a.
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment
of inattention while operating power tools may
result in serious personal injury.
b.
Use
personal
Always wear eye protection. Protective
equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal
injuries.
c.
Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d.
Remove any adjusting key or wrench
before turning the power tool on. A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e.
Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in unexpected
situations.
f.
Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in
moving parts.
g.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
4. Power tool use and care
a.
Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was designed.
b.
Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c.
Disconnect the plug from the power source
and/or the battery pack from the power tool
protective
equipment.
Publicidad
Tabla de contenido
