Using Anc/Transparency Mode; Multi-Point Operation; Adjusting The Volume - Beyerdynamic Blue BYRD ANC Instrucciones De Uso

Operation
Establishing pairing:
9 The in-ear headphones are switched off.
1 . Press the On/Off button for 4 s.
The Bluetooth® pairing mode
starts.
The LED display flashes alternately
blue and red.
2 . Activate the Bluetooth® function on
the playback device and search
for new devices if necessary.
3 . In the Bluetooth® menu on the
playback device, select "Blue Byrd
ANC (2nd gen.)" from the available
devices and pair the two devices
with each other.
After a successful connection, the LED briefly flashes
blue every 7 s. Each time the unit is switched on again,
the units will connect as soon as they are within range
of each other.
If the Bluetooth® connection has been lost, the LED briefly
flashes blue every 3 s.
Deleting the list of already paired devices:
► Press the On/Off button for longer than 10 s.
The list of already paired Bluetooth® devices
(maximum 8) is deleted, and the in-ear headphones
switch to the Bluetooth® pairing mode.

Using ANC/transparency mode

The Blue BYRD ANC (2nd generation) has three ANC
modes:
• ANC mode: Attenuation of ambient sound
• Transparency mode: Amplification of ambient sound
• Passive mode: ANC and transparency mode are deac-
tivated
Selecting ANC mode:
► Briefly press the On/Off push button once each time:
Passive mode > Transparency mode > ANC mode >
Passive mode > ...
A mode can be skipped by briefly pressing twice, e.g.
direct change from Passive mode to ANC mode.
The last selected mode is saved when the unit is switched
off.

Multi-point operation

The in-ear headphones can be paired with up to 8 Blue-
tooth®-enabled devices. Active connections are possible
with up to two devices at a time. However, playback of
music and phone operation is only possible with one
device at a time. Phone operation has priority over play-
back of music, i.e. playback of music is interrupted during
phone calls.
10/14
Priority list when using the playback devices (PD):
PRI . Profile
1 HFP (phone operation) PD 1 (device used first)
2 HFP (phone operation) PD 2 (device used second)
3 A2DP (playback of
music)
4 A2DP (playback of
music)
Setting up multi point:
1 . Connect the in-ear headphones with the first device
(see „Pairing with a playback device" on page 9).
2 . Deactivate the Bluetooth® connection on the first
device.
3 . Switch off the in-ear headphones.
4 . Connect the in-ear headphones with the second
device (see „Pairing with a playback device" on
page 9).
5 . Re-activate the Bluetooth® connection with the first
device that automatically connects to the in-ear
headphones.
Once both devices are paired with the in-ear
headphones, the in-ear headphones automatically
connect with both devices every time they are
switched on.
Using multi point:
9 You have connected the in-ear
headphones with two devices and
just activated media playback.
► Briefly press the ( ) once, to accept
an incoming call.
9 You have connected the in-ear
headphones with two devices and
have just ended a call.
► Briefly press the ( ) button once, to
start the media playback that was
last played.

Adjusting the volume

Increasing/decreasing the volume:
► In stages: briefly press the [+] / [–] button.
► Continuously: press and hold the [+] / [–]
button.
A signal tone sounds when the maximum/
minimum volume is reached.
Playback devices (PD)
PD 1 (device used first)
PD 2 (device used second)
Blue BYRD ANC (2nd generation)