MIRKA ARG-B 200 Instrucciones De Montaje página 347

In active mode the left LED shows the battery status:
Green: Battery charge level is OK.
Flashing green: Battery charge level is below 75%.
Flashing green/red: Battery charge level is below 50%.
Flashing red: Battery charge level or battery health (only available if intelligent battery is used) is under 25%.
Red: Battery voltage too low, tool is not operable.
The speed can be adjusted between 2500 and max 21000 rpm by adjusting the position of the trigger. In active mode
the max rpm can be adjusted by pressing rpm+ or rpm . The rpm can be adjusted in steps of 2500, 5000, 7500, 10000,
12500, 15000 and 21000 rpm.
The rpm can be locked to prevent an accidental rpm change. Wait until the tool is not in active mode. Simultaneously
press and hold both rpm+ and rpm buttons and then pull the switch trigger. In order to unlock the tool, repeat same
operation. If rpm+ or rpm is pressed in speed lock mode the right led flashes red twice but no speed change occur.
When grinding, if you just installed an accessory or are beginning a period of work, test it by letting it spin for one
minute before applying it to the workpiece. Allow accessory to come in to full speed before beginning work.
When grinding is finished, make sure the tool comes to a complete stop before laying th tool down. Remove the battery
from the tool by simultaneously pressing the button on both sides and removing the battery from the tool. Charge the
battery.
Bluetooth
This tool is equipped with Bluetooth® low energy technology and can be connected to an app from which additional
tool functionality can be accessed. For more information on the app functionality and if it is available in your country, go
to www.mirka.com/mymirka
Activate Bluetooth on your Mirka
Connect the battery to the tool.
1.
Press and hold the rpm+ button while activating the tool by pressing the switch trigger.
2.
3. Middle LED is flashing green, to indicate that Bluetooth is active and ready for connections.
4. Middle LED is lit green when the tool is connected to another Bluetooth device.
Bluetooth is deactivated when the tool is deactivated/turned off.
5.
NOTE! If the app is not installed or if it is not available in your country, Bluetooth shall not be activated.
The Bluetooth ® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such
marks by Mirka Ltd is under license. Other trademarks and trade names are those of their respective owners.
FCC Rules & Industry Canada s licence-exempt RSS
Compliance with the radio regulations in North America has been verified in accordance with FCC Part 15 subpart B and
C, RSS-GEN, RSS-247 and FCC §15.247. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
2.
NOTE! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION TO THE USER: Changes or modification not expressly approved by the party responsible for compliance could
void the user s authority to operate the equipment.
®
ARG-B 200 as follows:
Mirka® ARG-B 200 Cordless grinder
en | us-ca
347