Tabla de contenido
Solución de problemas
Manuales relacionados para Westinghouse Troy
Resumen de contenidos para Westinghouse Troy
- Página 1 ETL-ES-Troy-WH16 OWnEr'S ManuaL ManuaL dEL uSuariO Troy Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: net Weight: 16.28 LBS Peso neto: 7.4 KGS...
-
Página 2: Safety Tips
ETL-ES-Troy-WH16 SafETy TiPS OBSErVE THE fOLLOWinG: rEad and SaVE THESE inSTruCTiOnS WarninG: TO rEduCE THE riSK Of firE, ELECTriC SHOCK, Or PErSOnaL inJury, MOunT TO OuTLET BOX MarKEd 'aCCEPTaBLE fOr fan SuPPOrT Of 15.9 KG (35 LBS) Or LESS' and uSE MOunTinG SCrEWS PrOVidEd WiTH THE OuTLET BOX and/Or SuPPOrT dirECTLy frOM BuiLdinG STruCTurE. -
Página 3: Consejos De Seguridad
ETL-ES-Troy-WH16 COnSEJOS dE SEGuridad HaGa LO SiGuiEnTE: LEa y GuardE ESTaS inSTruCCiOnES adVErTEnCia: Para rEduCir EL riESGO dE inCEndiO, dESCarGa ELÉCTriCa O HEridaS GraVES PErSOnaLES, MOnTE En una CaJa dE EMBuTir rOTuLada “adECuada Para VEnTiLadOrES dE 15,9 KG (35 LB) O MEnOS” uTiLiZandO LOS TOrniLLOS dE MOnTaJE inCLuidOS COn La CaJa dE EMBuTir y/O MOnTE dirECTaMEnTE En La ESTruCTura dEL EdifiCiO La MayOrÍa dE LaS CaJaS dE EMBuTir uTiLiZadaS .nOrMaLMEnTE COn arTEfaCTOS dE iLuMinaCiÓn nO SOn adECuadaS Para VEnTiLadOrES y dEBErÍan SEr rEEMPLaZadaS. -
Página 4: Características
ETL-ES-Troy-WH16 fEaTurES CaraCTErÍSTiCaS DOWNROD INSTALLATION INSTALACIóN CON VARILLA VERTICAL For normal ceilings Para techo normales... -
Página 5: Preparing For Installation Antes De La Instalación
ETL-ES-Troy-WH16 PrEParinG fOr inSTaLLaTiOn anTES dE La inSTaLaCiÓn Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble). -
Página 6: Mounting Bracket Installation Instalación Con Soporte De Montaje
ETL-ES-Troy-WH16 MOunTinG BraCKET inSTaLLaTiOn MOunTinG OPTiOnS inSTaLaCiÓn COn SOPOrTE dE MOnTaJE OPCiOnES dE MOnTaJE Choose a MOunTinG OPTiOn Elija una OPCiÓn dE MOnTaJE nOrMaL dOWnrOd OPTiOn If installing downrod supplied with fan, proceed to page 7, step #5. OPCiÓn COn VariLLa VErTiCaL Para TECHO nOrMaL Si instala la varilla vertical incluida con el ventilador, proceda a la página 7, paso 5. - Página 7 ETL-ES-Troy-WH16 nOrMaL dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL Para TECHO nOrMaL Place downrod assembly into canopy (1), canopy cover ring (2) and coupling cover (3). Feed motor wires through the downrod assembly (4). Coloque el conjunto de la varilla vertical (1) dentro del dosel (1), el anillo de la cubierta Remove clamp pin (1) and cross pin (2) from downrod (3).
- Página 8 ETL-ES-Troy-WH16 nOrMaL dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL Para TECHO nOrMaL Loosen set screws (1) in downrod coupling (2). Insert downrod into downrod coupling. Make sure to align hole in downrod with the hole in downrod coupling. Install coupling cross pin (3) through coupling and downrod.
-
Página 9: Extended Downrod Option Opción Con Varilla Vertical Más Larga
ETL-ES-Troy-WH16 EXTEndEd dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL MÁS LarGa Loosen downrod ball (1) from downrod (2) by removing set screw (3). Slide downrod ball (1) off of downrod and remove pin (2). Afloje la bola de la varilla vertical (1) de la varilla vertical (2) quitando el Deslice la bola de la varilla vertical (1) hasta separarla de la varilla vertical tornillo (3). -
Página 10: Opción Con Varilla Vertical Más Larga
ETL-ES-Troy-WH16 EXTEndEd dOWnrOd OPTiOn OPCiÓn COn VariLLa VErTiCaL MÁS LarGa Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. note: Some extended downrods have a pre- drilled set-screw hole. -
Página 11: Montaje
ETL-ES-Troy-WH16 MOunTinG MOnTaJE Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje. Gire el ventilador hasta que la muesca de la bola de la varilla vertical (1) enganche sobre la saliente del... - Página 12 ETL-ES-Troy-WH16 WirinG OPTiOnS OPCiÓn dE CaBLEadO Make wiring connections from the house and the motor to the remote receiver as shown Once wiring step has been completed, slide the wired remote receiver in between the above. Connect using wire nuts (provided).
- Página 13 ETL-ES-Troy-WH16 SECurE TO CEiLinG aSEGurE EL VEnTiLadOr aL TECHO Loosen the 2 screws on the bottom of mounting bracket. (do not remove) Raise the canopy up and align the keyholes on the bottom of the canopy with the 2 screws on the bottom of mounting bracket.
- Página 14 ETL-ES-Troy-WH16 The inside canopy cover ring (1) has two keyhole slots that allow it to be mounted onto the screw heads on the two protruding screws from the mounting bracket. Slide the canopy cover ring up the downrod, and allow the two protruding screw heads from the mounting bracket to go into the keyhole slots on the canopy cover ring. Once engaged, twist the canopy cover ring to lock it onto the screw heads.
-
Página 15: Blade Installation Instalación De Las Aletas
ETL-ES-Troy-WH16 BLadE inSTaLLaTiOn inSTaLaCiÓn dE LaS aLETaS Check the fan for cardboard shipping stabilizer tabs located between the motor housing and the flywheel, and remove them if they are present. Insert the blades through the slots on the flywheel (1) as shown, aligning the holes in blades with the holes in the flywheel, and use the provided screws and washers to tighten. Repeat this step for remaining blades. -
Página 16: Light Fixture Installation Instalación Del Artefacto Luminoso
ETL-ES-Troy-WH16 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Remove one of the screws (1) on the switch housing plate (2), and loosen, (do not remove) the other two. Quitale uno de los tornillos (1) de la placa de la estructura del interruptor (2) y afloje (sin retirarlos) los otros dos. -
Página 17: Light Fixture Installation
ETL-ES-Troy-WH16 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Insert the wires from the fan through the middle hole in the metal decorative shade(1). Position both slots on the metal decorative shade directly under and in line with the two screws in the switch housing mounting plate. - Página 18 ETL-ES-Troy-WH16 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Remove two of the 4 screws on the metal decorative shade (1), and loosen (do not remove) the other two. Find the wire plugs from the light kit and from the motor and slide together.
- Página 19 ETL-ES-Troy-WH16 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO The light kit has 2 keyhole slots. Align the slots on the light kit to the protruding screws from the light kit support plate (1). Raise the light kit allowing the protruding screws from the support plate to enter the keyhole slots on the light kit.
- Página 20 ETL-ES-Troy-WH16 LiGHT fiXTurE inSTaLLaTiOn inSTaLaCiÓn dEL arTEfaCTO LuMinOSO Locate the indentations on the neck of the glass and align with the protrusions from the light kit. Lift the glass up allowing the protrusions to engage the indentations on the glass, and twist the glass clockwise to lock into place.
- Página 21 ETL-ES-Troy-WH16 Place the transmitter into the mounted holder. Mount wall bracket to the wall using screws provided. Coloque el transmisor en el soporte montado. Instale el soporte de pared sobre la pared con los tornillos incluidos.
- Página 22 ETL-ES-Troy-WH16 remote Control Operation NOTE: This remote uses 2 x AAA batteries. This remote control is preset with a pair of codes when manufactured. After installing the unit and restoring the power to your fan, press and hold the “OFF” button for 5 seconds. You must press the “OFF” button within 60 sec- onds of restoring power to the fan.
-
Página 23: Operation And Maintenance
ETL-ES-Troy-WH16 OPEraTiOn and MainTEnanCE Operation Turn on the power and check operation of fan. Reverse switch is located on the top of the motor housing. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. -
Página 24: Operación Y Mantenimiento
ETL-ES-Troy-WH16 OPEraCiÓn y ManTEniMiEnTO Operación Encienda el ventilador y verifique su funcionamiento. El encendor de march atras esta localizado el la parte superior del alojamiento del motor. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc. -
Página 25: Troubleshooting Guide
ETL-ES-Troy-WH16 If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some trOUBLESHOOtinG GUidE cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Troubleshooting chart. -
Página 26: Guía Para Solucionar Problemas
ETL-ES-Troy-WH16 Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación GUía Para SOLUCiOnar PrOBLEMaS o cableado incorrectos. En algunos casos, estos errores de instalación podrían ser confundidos con defec- tos. Si experienca algun fallo, consulte esta guía para solucionar problemas. Si no puede solucionar el problema, consulte a un electricista calificado y no intente reparar conexiones eléctricas. -
Página 27: Parts List
ETL-ES-Troy-WH16 PartS LiSt LiSta dE rEPUEStOS description 1 ..... . Mounting Bracket (1) 2 ..... . Blade (3) 3 . - Página 28 ETL-ES-Troy-WH15 Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation. Used under license by Westinghouse Lighting All rights reserved. Made in China...