Virutex FRB300 Manual De Instrucciones página 19

extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is una-
voidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appro-
priate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust related hazards.
h) Do not allow the familiarity with the frequent use of
tools to become complacent and ignore the principles
of tool safety. Negligence can cause serious injury in
a split second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any other
condition that may affect the power tools operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep the handles dry, clean and free of oil and grease.
The sliding handles do not allow safe handling and control
of the tool in unexpected situations. Power tools with
the switch on invite these situations.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
b) Use only original parts for repair and maintenance.
The use of incompatible accessories and parts can cause
electric shock and other injuries.
1.2 SAFETY INSTRUCTIONS FOR
HANDLING THE ROUTER
Special safety warnings
• Before work, inspection shall be carried out to see
whether the milling cutter is installed; you should fir-
mly hold the machine during work. Milling cutter with
appropriate dimension shall be used. Anytime when the
milling cutter is used or changed, it must be ensured
that switch on the machine is on off position. In order to
avoid personal injury done to you and your bystanders,
the power lines must be pulled out of the socket when
the milling cutter is assembled or changed.
• When the machine is used, you will work in dusty
environment; therefore, you should wear mask and
goggles. If you have long hair, you shall wear hair care
cap. You shall not wear loose clothes during work.
• Before the machine is removed from the workpiece,
you shall cut off power switch and completely stop the
milling cutter.
• The hands shall always be far away from the rotating
parts. When the milling cutter is in contact with the
workpiece, you shall not make an attempt to start the
machine.
• After work, the switch shall be turned off first and
then lock knot of guide pillar shall be loosed to make
the machine return to original position.
Safety guidelines during power tool operation
19