Dust Collection - Virutex FRB300 Manual De Instrucciones

8.4 INSTALLING / ADJUSTING / REMOVING OF
THE ADJUSTING GUIDE (SEE PART 4-5)
The guide 19 is used for milling edges with router bits
which do not have support bearings at the end.
• Install the guide 19 on the base plate 14 and fix it
with the setscrew 17 (see Fig. 4).
• You can adjust a vertical position of the guide 19
depending on the router bit used and the thickness of
the workpiece (see Fig. 5.1):
• Loose the setscrew 17;
• Move the guide 19 up or down;
• Tighten the setscrew 17.
• You can adjust a horizontal position of the guide 19 to
define the thickness of material removal (see Fig. 5.2):
• Loose the fixing screw 27;
• Rotate the lead screw 28 to move the holder 29 to
set the thickness of material removal (distance "a");
• Tighten the fixing screw 27.
• Disassembly operations do in reverse sequence.
8.5 INSTALLATION / ADJUSTMENT / DISMANT-
LING OF THE PARALLEL GUIDE (SEE FIG. 6-7)
Parallel guide 18 enables milling along the straight line
side surface of the workpiece.
• Install the holder 31 on the base plate 14 and secure
it with the setscrew 17 (see Fig. 6.1).
• Assemble parallel guide 18 as shown in (Fig. 6.2).
• You can adjust the offset from the workpiece edge:
• Loose the wing nut 35 (see Fig. 7.1);
• move the guide 34 to set the offset from the
workpiece edge (see Fig. 7.2);
• Tighten the wing nut 35 (see Fig. 7.1).
• Disassembly operations do in reverse sequence.
9. OPERATION AND ADJUSTMENTS OF THE TOOL
Recommendations on the power tool operation
9.1 SETTING MILLING DEPTH (SEE FIG. 9-10)
The adjustment of the milling depth may
only be carried out when the power tool
switched off, and also switched off stan-
dby mode (LED lamp 12 will be not lit).
• Install the power tool on the even horizontal surface.
• Open the latch 15, as shown in (Fig. 9.1).
• Rotate the twist knob 16 to move the body of the
power tool (see Fig. 9.2).
• Lower the power tool body, so that the end of the
router bit could touch the work piece surface (see Fig.
10.1). As a result, you have locked the "zero position".
• To set the milling depth (distance "b"), rotate the
twist knob 16 in the direction shown in (Fig. 10.2) (the
body of the power tool will lower) to set milling depth.
24
Use the scale 5 when setting milling depth.
• Close the latch 15, as shown in (Fig. 9.3).
9.2 MILLING DIRECTION
Milling should always be performed
against the router bit rotation direction.
Otherwise, the power tool will be subject
to jerks, which may result in the loss of
control over it.
9.3 GENERAL OPERATIONAL
RECOMMENDATIONS
• Mark out and fix the treated workpiece.
• Set the required milling depth, as described above.
• When using the guide 19 or the parallel guide 18,
adjust them as described above.
• Turn on the power tool.
• Mill with uniform flow holding the power tool firmly
and following recommendations regarding the direction
of milling. Do not push excessively - it takes some time
to complete the process. Excessive force will not speed
up the work process, but it will overload the power tool.
•Turn the power tool off.
9.4 GUIDE WITH A ROLLER (SEE FIG. 11)
The guide 19 is used for milling edges with milling
cutters which do not have support bearings at the end.
Milling along the curved side surface is allowed (see
Fig. 11.2).
• Install the guide 19 onto base plate 14 and adjust its
position as described above.
• Mill by pressing the roller 30 against the side surface
of the workpiece (see Fig. 11.1 and 11.2).
9.5 PARALLEL GUIDE (SEE FIG. 12)
Parallel guide 18 enables milling along the straight line
side surface of the workpiece.
• Install the parallel guide 18 on the base plate 14, and
adjust its position as described in (point 8.5 INSTALLATION
/ ADJUSTMENT / DISMANTLING OF THE PARALLEL GUIDE)
• Set the space from the work piece brim by adjusting
the parallel guide 18, as described in (point 8.5 INSTA-
LLATION/ADJUSTMENT/ DISMANTLING OF THE PARALLEL
GUIDE)
• Perform the milling operation by pressing parallel
guide 18 to the side surface of the workpiece.

10. DUST COLLECTION

Remove the battery from the power tool
before carrying out work on the power tool.