Installing And Removing The Battery Pack; Helpful Hints - DeWalt DCS353 Manual De Instrucciones

during use. DO NOT suspend tool overhead or suspend
objects from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook
is secure.
iMPORTAnT: When attaching or replacing the belt hook,
only use the screw 26 that is provided with the belt hook.
Be sure to securely tighten the screw.
To accommodate left- or right- handed users the belt
hook can be attached to the tool using one of the
25
slots below the main handle on left or right side and using
the provided screw installed on the underside of the
26
main handle.
If the belt hook is not desired at all, it can be removed from
the tool.
To Install the Belt Hook
1. Insert the hook into one of the slots, on left or right side,
below the main handle.
2. Install the screw on the underside of the main handle. Be
sure to securely tighten the screw.
To Remove or Move the Belt Hook
1. Remove the screw located on the underside of the
main handle.
2. Pull the belt hook away from the main handle.
3. Insert the hook into one of the slots, on left or right
side, below the main handle, or install the screw on the
underside of the main handle. Be sure to securely tighten
the screw.
OPERATION

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Proper Hand Position (Fig. M)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle 10 .

Installing and Removing the Battery Pack

(Fig. D)

WARNING: Ensure the switch is in the off position
before inserting battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button 9 and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
into the tool handle, align the
8
Instructions for Use (Fig. A)
1. Install the battery pack.
2. To turn the tool ON, hold it as shown in Figure M and
press the variable speed trigger
nOTE: The further the trigger switch is depressed the
faster the tool will operate. If in doubt about the proper
speed for your operation, test the performance at low
speed and gradually increase until a comfortable speed
is found.
3. To turn the tool OFF, release the variable speed
trigger 1 .
Lock on/off Button (Fig. N)
The tool can be locked off by fully depressing the lock on/off
button 4 to the left until it "clicks" as shown in Figure N.
Pushing the lock on/off button
trigger depressed will lock the trigger in the depressed
1
position. This allows for more comfort and control in
extended use applications.
Pressing the trigger switch again will release the lock out and
the tool will turn off upon release of the trigger.
nOTE: The tool will automatically shut off after operating
for five minutes with the lock-on button engaged. To restart
the tool, the user will have to release the trigger and repress
lock-on button.
LED Worklight (Fig. O)
The LED worklight 2 will activate when the trigger is
depressed. It will automatically shut off following a short
period of time once the trigger is released.
Using the Dust Extraction Adaptor with
the Sanding Platen (Fig. R)
Optional Accessory
1. Attach the dust extraction adaptor
Attaching the Dust Extraction Adaptor.
2. Attach the sanding platen
Installing/Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. S)
Optional Accessory
1. Attach the dust extraction adaptor. Refer to Attaching
the Dust Extraction Adaptor.
2. Push dust extraction arm
the dust extraction adaptor
3. Attach plunge cutting blade as described under
Installing/Removing Accessories.
4. Adjust the dust extraction arm

Helpful Hints

• Always ensure the workpiece is firmly held or clamped to
prevent movement. Any movement of the material may
affect the quality of the cutting or sanding finish.
English
.
1
to the left with the
4
18 . Refer to
as described under
23
20 into the lower aperture of
18 .
20 for best results.
13