Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Intended use
The tool is intended for hammer drilling and drilling in
brick, concrete and stone as well as for chiselling work.
It is also suitable for drilling without impact in wood,
metal, ceramic and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN60745-2-6:
Model HR008G
Sound pressure level (L
Sound power level (L
) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR009G
Sound pressure level (L
Sound power level (L
) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR008G with DX10
Sound pressure level (L
Sound power level (L
) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Model HR009G with DX11
Sound pressure level (L
Sound power level (L
) : 105 dB (A)
WA
Uncertainty (K) : 3 dB(A)
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
) : 94 dB(A)
pA
) : 94 dB(A)
pA
) : 94 dB(A)
pA
) : 94 dB(A)
pA
Vibration
The following table shows the vibration total value
(tri-axial vector sum) determined according to applica-
ble standard.
Model HR008G
Work mode
Vibration
emission
Hammer
9.1 m/s
drilling into
concrete
(a
)
h, HD
Hammer
7.8 m/s
drilling into
concrete with
DX10 (a
)
h, HD
Chiselling func-
8.0 m/s
tion with side
grip (a
)
h, Cheq
Drilling into
5.1 m/s
metal (a
)
h, D
Model HR009G
Work mode
Vibration
emission
Hammer
9.1 m/s
drilling into
concrete
(a
)
h, HD
Hammer
7.3 m/s
drilling into
concrete with
DX11 (a
)
h, HD
Chiselling func-
7.1 m/s
tion with side
grip (a
)
h, Cheq
Drilling into
2.5 m/s
metal (a
)
less
h, D
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
13 ENGLISH
Uncer-
tainty (K)
2
2
1.5 m/s
2
2
1.5 m/s
2
2
1.5 m/s
2
2
1.5 m/s
Uncer-
tainty (K)
2
2
1.5 m/s
2
2
1.5 m/s
2
2
1.5 m/s
2
2
or
1.5 m/s
The vibration emission during
Be sure to identify safety mea-
Applicable
standard
EN60745-2-6
EN60745-2-6
EN60745-2-6
EN60745-2-1
Applicable
standard
EN60745-2-6
EN60745-2-6
EN60745-2-6
EN60745-2-1
Publicidad
Tabla de contenido
