Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE: To make deeper holes, remove the core bit,
break and remove the core, then resume drilling.
When drilling long or deep holes, after each inch
of penetration pull the bit partially out of the hole
while the tool is running, to help clear dust from
the bit flutes. Dust can clog the bit flutes and can
make the bit bind in the hole. If this occurs, stop
the tool, free the bit and begin again.
Drilling Large Diameter Holes
with Core Bits
When drilling holes with large diameter core bits, dust
may build up in the cut and can cause the tool to
stall, bind, or cut slowly. By creating an opening for
the dust to escape, drilling time, bit stress, and tool
stress can be reduced.
1. Start the cut as normal.
2. Once the bit is firmly established in
the cut (about 1/4" deep), remove
the bit from the cut.
3. Remove the bit from the tool.
4. Install a standard fluted bit, ap-
proximately 7/8" in diameter, onto
the tool.
5. Drill a perpendicular hole through
the kerf of the large hole.
• Depending on the location of the
work, the hole should either break
through the other side of the hole/
floor or extend 4"-5" past the end
of the workpiece (such as into the
dirt below a concrete slab).
• If dust builds up in the hole, vac-
uum it out and continue drilling.
• If drilling through a wall, the hole
for dust should be drilled on
the lowest part of the large
hole kerf as the dust will fall
there when drilling and can be
evacuated more easily.
6. Reinstall the core bit and con-
tinue drilling. Dust and debris
will fall through the hole and
optimize the cutting ability of
the bit.
NOTE: If unable to drill a hole
in the kerf, pull back on the bit
with the hammer running. This
will remove some of the dust
and debris from the cut. Repeat
this for every inch of drilling. If
necessary, vacuum dust and
debris from the cut and sur-
rounding area.
7. For core bits, once the maximum
core bit depth is drilled, the core
must be broken and removed.
• Install a chisel bit.
• Place the chisel into the hole
kerf.
• Chisel down into the kerf at
several points until the core is loose or broken.
• Remove the core and vacuum/remove any re-
maining dust and debris.
• Install the core bit and continue the cut.
WARNING
• Always use the "hammering-only" setting to
set the anchor. Never use the "hammering-with-
rotation" setting to set the anchor.
• Never switch the tool to "hammering-with-
rotation" until after the anchor has been set and
the tooth anchor chuck has been removed from
the anchor.
MILWAUKEE Tooth Anchor Chucks require a "B"
taper adapter.
1. Place the proper size tooth anchor chuck into the
"B" taper adapter. Then insert the "B" taper adapter
into the tool and lock it into place as described.
See "Installing Bits and Chisels".
2. Insert the anchor into
Cut
approximately
the tooth anchor chuck.
1/4" deep with
a core bit.
Set the knob for ham-
mering only. Set the
anchor on your mark
and hammer until the
teeth have penetrated
Drill a hole
the concrete.
through the
3. Set the knob for ham-
work.
mering with rotation
and drill until the chuck
is 1/8" above the con-
crete.
Top view
NOTE: It may be nec-
essary to clean dust
Dust and debris
and cuttings from the
Dust and debris
will fall through
will fall through
anchor several times
the hole.
the hole.
while drilling the hole.
Use caution to prevent
exposure to dust.
4. Remove the anchor
Side view
of slab
from the hole while the
tool is running. Clean
the dust and cuttings
from the anchor by
pointing it downward and turning the tool on and
off several times. Clean the dust out of the hole
with a vacuum cleaner or blowout bulb.
5. Place the expansion plug into the anchor and insert
Pull bit out as far
the anchor into the hole. Switch the knob back to
as possible once
hammering only, and hammer the anchor firmly
or twice per inch
into the hole.
drilled.
6. Snap the head off of the
anchor. To remove the
head of anchors up to
5/8", grasp the handles
firmly and pull the tool
sharply towards you or
snap off the anchor
head with a hand ham-
mer as shown. The
anchor is now ready to
receive a bolt.
7. To remove the an-
chor head wedged
in the tooth anchor
chuck, use drift pin
48-86-0100.
8. To remove the tooth anchor chuck, remove the
"B" taper adapter from the nose of the tool. Insert
the drift pin supplied with the adapter into the hole
on the side of the "B" taper adapter and strike it
sharply to force out the tooth anchor chuck.
6
To reduce the risk of personal in-
jury and damage to the tool or work:
Setting Self-Drilling Anchors
1/8"
Publicidad
Tabla de contenido
