Technical Data; Before Starting The Equipment - EINHELL GC-CH 1855/1 Li Manual De Instrucciones

4. Technical data

Rated voltage ..........................................18 V d.c.
Cutter rail length ..................................... 620 mm
Cutting length ......................................... 550 mm
Tooth spacing ........................................... 18 mm
Cuts/min ...................................................... 2200
Sound pressure level, L
K uncertainty .............................................. 3 dB
pA
Sound power level, L
WA
K uncertainty .......................................... 2.5 dB
WA
Sound power level guaranteed L
Vibration a ......................................... 1.494 m/s²
h
K uncertainty ........................................... 1.5 m/s²
Weight ........................................................2.4 kg
Power X-Change lithium-ion batteries
Voltage: .................................................. 18 V DC
Capacity: ...................................... 2.0 Ah | 2.5 Ah
Number of cells: ................................................ 5
Power X-Charger battery charger
Input voltage: .....................200-250 V ~ 50-60 Hz
Output voltage: ....................................... 20 V DC
Output current: ............................................... 3 A
Protection class:............................................II /
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
Anl_GC_CH_1855_1_Li_SPK13.indb 17
GB
..................... 82 dB (A)
pA
...................... 91.7 dB (A)
........ 94 dB(A)
WA
- 17 -
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

Fitting the hand guard
Attach the hand guard (Fig.1/Item 2) in the di-
rection of the arrow as shown in fi gure 4a. Next,
fasten this with the 2 screws (Fig. 2/Item 10) as
shown in Fig. 4b.
Assembly of the steady grip
Attach the steady grip (Fig. 2/Item 3) in the direc-
tion of the arrow as shown in Fig. 4c.
Important: The lock (Fig. 4c/Item 11) must be
on the right-hand side! Make sure that the
electrical contacts are connected correctly.
Then fully tighten the screw (Fig. 4d/Item 12) with
the lock closed (Fig. 4c/Item 11).
Adjustable steady grip
The steady grip is adjustable. Loosen the lock
(Fig. 4c/Item 11) by opening, bring the steady grip
into the desired position and attach it again by
closing the lock (Fig. 4c/Item 11).
31.05.2022 10:57:37