Intended Use; Safety Instructions; Maintenance And Cleaning - ARRI Orbiter Manual De Usuario

Intended use

This product is an accessory for the „Orbiter" luminaire. It is intended to
illuminate persons and objects.
Always follow the safety information.
Any usage other than described above is not permitted and can damage
the product and lead to associated risks such as short-circuit, fire, elec-
tric shock, etc. You are not allowed to modify the product.
This product fulfills all legal requirements.

Safety Instructions

•
Please read and observe all instructions delivered with the product
before use. The instructions contain important information for safe
handling.
• Please keep all instructions delivered with the product for possible
subsequent owners.
• Caution - breaking glass. Replace a broken glass immediately.
Do not use an accessory with broken glass.
• Caution - finger crushing. Take care not to crush your fingers when
closing the top latch (1) or when inserting an accessory into the ac-
cessory brackets (3, 4).
• Sharp edge! Do not touch the secondary reflector (10).
The user must:
• Be qualified for the appropriate use of the accessory.
• Follow the user manual.
• Ensure safe usage.
• Use the product in accordance with regulations.
• Follow the latest regulations and standards.
ARRI is not liable for damages caused by improper use or incorrect
operation.
To Mount the Fresnel Lens
• Remove the protective cap both from the Quick Lighting Mount and
from the Fresnel Lens.
• Align the locking pin (11) with the guide for the locking pin (14) and
insert the Fresnel Lens in the Quick Lighting Mount.
• Turn the Fresnel Lens clockwise, until the locking slider (13) audi-
bly engages. The Fresnel Lens can not be turned counter-clock-
wise if the locking slider is engaged full.
• The Fresnel Lens must be secured with a suitable safety cable.
Pass the safety cable through the safety loop attachment (2) of the
Fresnel Lens and the supporting structure or the upper handle of
the Orbiter.
Always secure the Fresnel Lens against falling with a safety cable
if the primary catch fails!
Automatic Optic Recognition
The digital optics interface of the Quick Lighting Mount recognizes when
the Fresnel Lens is attached to the luminaire. It adapts the light output
for best performance. If the digital optics interface fails to recognize the
attached Fresnel Lens correctly, please clean the contacts as described
in the Orbiter „Safety and Installation Manual" which is available for free
download on the ARRI website.
To Remove the Fresnel Lens
• Remove the safety cable from the Fresnel Lens.
• Push the locking slider (13) inwards and turn the Fresnel Lens
counterclockwise until it stops.
• Remove the Fresnel Lens and place the protective cap both on the
Quick Lighting Mount and the Fresnel Lens.
To Operate the Fresnel Lens
You can change the beam angle of the light beam motor driven between
15° and 65°.
To change the beam angle of the Fresnel Lens:
• Turn the knob (6) clockwise or counter-clockwise to modify the
beam angle. The beam angle is shown in the display (5).
• Open the appropriate menu of the Orbiter control panel and set the
beam angle.
• Set the beam angle via DMX. The latest DMX protocol is available
on the ARRI web site www.arri.com.
To change the brightness of the display (5):
• Set the brightness via the appropriate menu of the Orbiter Control
Panel.
The control panel user manual is available for free download on the
ARRI Orbiter website.
To Use Accessories with the Fresnel Lens
You can use accessories like barndoors or filter frames with the
Fresnel Lens. The Fresnel Lens accepts accessories with
330 mm / 13.0 in or 344 mm / 13.5 in diameter.
To use accessories with the Fresnel Lens:
• Press the knob of the top latch (1) to open the top latch.
• Insert the accessory in the accessory brackets (3, 4) on the front of
the Fresnel Lens. The inner slots are designed to hold accessories
with 330 mm / 13.0 in diameter, while the outer slots are designed
to hold accessories with 344 mm / 13.5 in diameter.
• Ensure that the accessory is held safely in the appropriate acces-
sory brackets and accessory slot.
• Only for accessories with 344 mm / 13.5 in diameter: Ensure that
the second catch on the lower bracket (4) engages properly.
• Close the top latch. Ensure that the top latch is closed properly.
• The accessory must be secured with a suitable safety cable. Pass
the safety cable through the safety loop attachment of the Fresnel
Lens (2) and the supporting structure or the upper handle of the
Orbiter.
To remove an accessory from the Fresnel Lens:
• Press the knob of the top latch (1) to open the top latch.
• Only for accessories with 344 mm / 13.5 in diameter: Press and
hold the knob on the lower bracket (4) to disengage the second
catch.
• Remove the accessory.

Maintenance and Cleaning

Inspect the product regularly for visible damage.
• Do not use a damaged, deformed or dirty product.
• Remove loose dust and dirt by vacuuming or blowing out with low-
pressure compressed air.
• Remove greasy deposits with a soft, lint-free cloth moistened with
plastic cleaner. You can also use benzene-free petroleum ether or
isopropanol. The cleaning agent must not contain benzene, etha-
nol, alcohol, organic substances or thinner. Dry the product with a
soft, lint-free cloth
ARRI Service
In case of technical problems please visit us at:
www.arri.com
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
Global Application & Services
Flintsbacher Strasse 1-5
D-83098 Brannenburg
Germany
Design and specifications are subject to change without notice