Stanley FATMAX FMC626 Traducido De Las Instrucciones Originales página 9

Screw driving
For driving fasteners, the forward/reverse button should
u
be pushed to the left.
Use reverse (button pushed to the right) for removing
u
fasteners.
Note: When moving from forward to reverse, or vice versa,
always release the trigger switch first.
Drilling
Use sharp drill bits only.
u
Support and secure work properly, as instructed in the
u
Safety Instructions.
Use appropriate and required safety equipment, as
u
instructed in the Safety Instructions.
Secure and maintain work area, as instructed in the
u
Safety Instructions.
Run the drill very slowly, using light pressure, until the
u
hole is started enough to keep the drill bit from slipping out
of it.
Apply pressure in a straight line with the bit. Use enough
u
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
Hold the drill firmly with two hands, one hand on the han‑
u
dle, and the other gripping the bottom around the battery
area or the auxiliary handle if provided.
DO NOT CLICK THE TRIGGER OF A STALLED DRILL
u
OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE
TO THE DRILL CAN RESULT.
Minimize stalling on breakthrough by reducing pressure
u
and slowly drilling through the last part of the hole.
Keep the motor running while pulling the bit out of a drilled
u
hole. This will help reduce jamming.
Make sure switch turns drill on and off.
u
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
Drilling in masonry
For drilling in masonry, set the collar (3) to the hammer
drilling position by aligning the symbol with the marking. Use
carbide tipped masonry bits. Refer to Drilling section. Keep
even force on the drill but not so much that you crack the brit‑
tle material. A smooth, even flow of dust indicates the proper
drilling rate.
(Original instructions)
LED work light
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Bit tip storage
A bit storage slot (9) is built into the base of the tool.
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack
not charged.
Unit starts immedi‑ The switch has been
ately upon inserting left in the "on" posi‑
battery tion.
Battery pack will Battery pack not
not charge. inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off Battery pack has
abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Maintenance
Your Stanley Fat Max tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
ENGLISH
Possible solution
Check battery pack
installation.
Check battery pack charg‑
ing requirements
The switch must be
moved to "off" to prevent
the tool from immediately
starting when battery is in‑
serted.
Insert battery pack into
charger until LED lights.
Plug charger into a work‑
ing outlet.
Move charger and battery
pack to a surrounding
air temperature of above
40 degrees F (45ºC) or
below 105 degrees F
(+40.5ºC)
Allow battery pack to cool
down.
Place on charger
and allow to charge.
9