5.
Using the D
WALT
Tool Connect™ application, select the product type (Rotary
®
E
Laser Detector) and pair your cell phone to the Detector.
• When the laser is on, the DEWALT
information about the laser via the detector.
• A laser safety icon to let you know the laser is on.
• The laser's current settings for RPM, Slope, etc.
• If the current settings are one of the "favorite settings" you have saved for
the laser, it will display the name of that setting (e.g., Main St - Site 3).
• If the laser is dropped, disturbed, etc., it will send messages to the
Tool Connect™ application to inform you.
• If the Tracking feature is on, the application will know where the laser is
and will let you know if the laser has been taken and is now out-of-range.
Accessories
Recommended accessories for use with your tool are available for purchase at
your factory-owned local service center.
WARNING:
Since accessories other than those offered by D
tested with this laser, use of such accessories with this laser could be
hazardous. To reduce the risk of injury, only use D
that are recommended for use with this rotary laser.
If you need assistance in locating any accessory, please visit our website
www.D
WALT.com
e
Mounting Bracket
Some laser kits include a mounting bracket, which can be used for attaching the
tool to a track or to a ceiling grid to aid in acoustical ceiling installation. Follow
the directions below for using the mounting bracket.
CAUTION:
Before attaching the laser level to wall track or ceiling angle, be
sure that the track or angle is properly secured.
1.
Place the laser on the mounting base (Figure
screw hole on the tripod adapter (Figure
the laser with the hole (Figure
2.
Turn the mounting knob (Figure
3.
With the bracket's measuring scale (Figure
clamp locking knob (Figure
P 8
All manuals and user guides at all-guides.com
Tool Connect™ application will display
®
WALT have not been
E
WALT
accessories
®
E
) aligning the 5/8–11
P 5
), attached to the bottom of
G 1
) in the mounting base.
P 6
) to secure the laser.
P 3
) facing you, loosen the
P 7
) to open the clamp jaws.
4.
Position the clamp jaws around the wall track or ceiling angle and
tighten the clamp locking knob (Figure
onto the track. Be sure that the clamp locking knob is securely tightened
before proceeding.
CAUTION:
Always use a ceiling wire hanger or equivalent material, in addition
to the clamp locking knob, to help secure the laser level while
mounting it to a wall. Thread the wire through the handle of the
laser level. DO NOT thread the wire through the protective metal
cage. Additionally, screws may be used to fasten the bracket
directly to the wall as a backup. Screw holes (Figure
located at the top of the bracket.
5.
Using the base leveling knob (Figure
from the wall.
6.
The tool can be adjusted up and down to the desired height for working.
While supporting the mounting base, loosen the locking knob on the left
side of the bracket (Figure
P 1
7.
Turn the adjustment knob on the right side of the bracket (Figure
move the laser level up and down to set your height. Use the measuring
scale (Figure
) to pinpoint your mark.
P 7
NOTE: It may be helpful to turn the power on and turn the rotary head so
that it puts a dot on one of the laser scales. The DeWALT target card is
marked at 1–1/2" (38 mm), so it may be easiest to set the offset of the laser
to 1–1/2" (38 mm) below the track.
8.
Once you have positioned the laser at the desired height, tighten the
locking knob (Figure
) to maintain this position.
P 1
Construction Grade Rod
DANGER:
NEVER attempt to use a grade rod in a storm or near overhanging
electric wires. Death or serious personal injury will occur.
Some laser kits include a grade rod. The D
measurement scales on both sides and is constructed in telescoping sections.
A spring-loaded button actuates a lock to hold the grade rod at various lengths.
The front of the grade rod has the measurement scale starting at the bottom.
Use this for measuring from the ground up when grading or leveling jobs.
The back of the grade rod is designed to measure the height of ceilings, joists,
etc. Fully extend the top section of the grade rod until the button locks into the
previous section. Extend that section either until it locks into the adjacent section
or until the grade rod touches the ceiling or joist. The height is read where the
last extended section exits the previous lower section (Figure
) to close the clamp jaws
P 8
) are
P 9
) approximate a level position
P 2
).
P 4
WALT Grade Rod is marked with
e
).
Q
E
) to
19