Safety Warnings For Sander - Bosch PBS 75 A Manual Original

12 | English
Remove any adjusting key or wrench before turning
u
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal in-
jury.
Do not overreach. Keep proper footing and balance at
u
all times. This enables better control of the power tool in
unexpected situations.
Dress properly. Do not wear loose clothing or jew-
u
ellery. Keep your hair and clothing away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
If devices are provided for the connection of dust ex-
u
traction and collection facilities, ensure these are con-
nected and properly used. Use of dust collection can re-
duce dust-related hazards.
Do not let familiarity gained from frequent use of tools
u
allow you to become complacent and ignore tool
safety principles. A careless action can cause severe in-
jury within a fraction of a second.
Power tool use and care
Do not force the power tool. Use the correct power
u
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was de-
signed.
Do not use the power tool if the switch does not turn it
u
on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or re-
u
move the battery pack, if detachable, from the power
tool before making any adjustments, changing ac-
cessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally.
Store idle power tools out of the reach of children and
u
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools and accessories. Check for mis-
u
alignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
1 609 92A 83R | (04.07.2022)
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.

Safety Warnings for Sander

Hold the power tool by insulated gripping surfaces,
u
because the sanding surface may contact its own
cord. Cutting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an
electric shock.
Only use the power tool for dry sanding. Water entering
u
a power tool will increase the risk of electric shock.
Switch the power tool on before making contact with
u
the workpiece and only switch the power tool off after
you have removed it from the workpiece. The power
tool can move suddenly.
Never touch the sanding belt while it is running. This
u
poses a risk of injury.
Wear protective gloves and never touch the sanding
u
belt while it is running. This poses a risk of injury.
Ensure that no persons are at risk due to flying sparks.
u
Remove combustible materials from the surrounding
area. Flying sparks are created when sanding metals.
Do not use any worn, torn or severely clogged sanding
u
belts. Damaged sanding belts can tear, fly off and injure
someone.
Warning: Danger of fire! Avoid overheating the work-
u
piece and the sander. Always empty the dust collector
before taking a break from work. Sanding dust in the
dust bag, microfilter, paper bag (or in the filter bag or va-
cuum cleaner filter) can spontaneously combust under
certain conditions, for example if flying sparks are cre-
ated when sanding metals. This risk is increased if the
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Bosch Power Tools