EN
DESCRIPTION
Fixed inductor for the supply of ink. Operated by compressed air. This
unit uses two pneumatic cylinders connected with a metal structure and
protected with metal fairing fixed to a reinforced base plate, resulting in
a very robust piece of equipment that is very small for the type of drums
with which it can work.
This unit, supplied with all the components necessary for its use, was designed
to supply ink with the greater guarantee of priming of the pump, and
maximum use of the ink drums, compatible with this model of inductor.
It incorporates a robust steel inductor plate, which has a sealing system
made up of lip seals or O-rings. This system guarantees the walls of the
WARNING AND CAUTIONS
!
WARNING: This symbol aware of serious bodily injury or death
if you ignore the warning described.
READ BEFORE USE
!
WARNING
•
Read all instruction manuals, tags, and labels before operating the
equipment. This equipment is for professional use only.
•
The non compatible fluids may cause damage in the pump and
serious personal injury.
•
The pump generates high or very high pressures. Do not exceed
the maximum air inlet pressure of 10 bar.
•
Do not exceed the drum's pressure limits. Be sure of the drum's
pressure limitations and regulate the pressure within the safety
limits when supplying air to the inductor plate. Do not try to use
the unit until you have taken all possible precautions to guarantee
that the unit has been installed correctly and that the base has been
firmly secured to the concrete floor.
•
Avoid electrical discharges. Ensure there are no electrical cables,
devices or accessories above the hoist. Examine the work area and
take the measures necessary to ensure that enough space is
maintained for the installation of the hoist and for the pump to be
lifted as much as possible and that they work correctly.
•
Maintain a minimum safety distance when raising and lowering the
inductor. Do not get too close; operate it from a safe place, so you
cannot get trapped between the unit and its mobile elements. Take
care when inserting the inductor plate into the drum.
•
When not in use, be sure to shut off the air supply to avoid
accidents.
•
The unit speed has been regulated by manufacturer. To engure
sage operation of this unit. Do not modify the speed.
2
854 803 R. 05/21
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
drum are clean and that it is perfectly sealed, which stops impurities
getting in or simply protects from the weather. The model and material
of the lip or seal used depends on its compatibility with the substance
pumped. There are also different pump kits designed to optimise the
work depending on the use required of this unit.
When the unit is correctly secured, the plate can be raised together with
the pump to a given height to facilitate changing the used drum.
This unit has a control cabinet for the inductor and for the pump
installed in the unit. This control cabinet has all the systems necessary to
facilitate the inductor plate going into and out of the drum.
!
:
CAUTION
This symbol aware of personal injury or property
damage if you ignore the caution described.
•
If follower plate is jammed with the drum. Be careful in the
extraction, the unit could move violently and unexpectedly.
•
An improper use of this machine can cause injuries to people or
things.
•
Use products and solvents that are compatible with the various
parts of the equipment, and read the manufacturer's warnings
carefully
•
Do not alter or modify this equipment. Check the equipment for
worn parts once a day. If any worn parts are found, replace them
using ONLY original spare parts
•
Do not wear bracelets, earrings, rings, chains, or anything else that
may hinder the operator's work.
•
Wear clothing that complies with the safety standards in force in
the country in which the equipment is used.
•
Do not wear clothing with wide sleeves, scarves, ties, or any other
piece of clothing that could get tangled up in moving parts of the
equipment during the work, inspection, or maintenance cycles.
•
The employer shall train its employees about all those risks
stemming from accidents, about the use of safety devices for their
own safety and about the general rules for accident prevention in
compliance with international regulations and with the laws of the
country where the plant is used.
•
The behaviour of the employees shall strictly comply with the
Accident prevention and also environmental regulations in force in
the country where the plant is installed and used.