MSW Motor Technics C-SAW210N Manual De Instrucciones página 5

TECHNICAL DETAILS
Product name Circular Saw
Model C-SAW210N
Rated voltage [V~]/Frequency [Hz] 230/50
Power [W] 900
Max power consumption [W] 1200W S6 40%
Protection class II
Working mode S6
Maximum rotational speed 4800
(without load) [rev/min]
Maximum cutting depth at 90° 45
[mm]
Maximum cutting depth at 45° 27
[mm]
Blade tilt range 45°~90°
Dimensions [mm] 580x440x360
Table dimensions [mm] 525x440
Blade diameter [mm] 210
Blade bore size [mm] 30
Splitting wedge thickness [mm] 2.2
Sound power level L 105,4 dB (A)
WA
Uncertainty
K=3 dB(A)
Sound pressure level L 92,4 dB (A)
pA
Uncertainty
K=3 dB(A)
Number 24
of saw teeth
Weight [kg] 11,35
USAGE PURPOSE
The device is designed for cutting wood.
Any damage resulting from a non-conform use of the
device is payable by the user!
PRINCIPLE OF OPERATION
6
4
Assembly
7
1 2 3 5
8
9
10
11
18
17
13 12
15 14
16
8
6 19 5
1. Worktable
2. Groove
3. Angle cutting guide
4. Guide knob
5. Splitting wedge
6. Blade guard
7. Saw blade
8. Base insert
9. Parallel guide
10. Parallel guide mounting bolt
11. Scale
12. Blade height adjustment knob
13. Blade tilt angle adjustment knob
14. Overload breaker
15. Switch On/Off
16. Rubber pads
17. Push stick bracket
18. Push stick
19. Blade guard mounting bolt
BEFORE FIRST USE
Upon receipt of the goods, check the packaging for
integrity and open it. If the packaging is damaged, please
contact your trans¬port company and distributor within 3
days, and document the damages as detailed as possible.
Do not turn the package upside down! When transporting
the package, please ensure that it is kept horizontal and
stable. Please keep all packaging materials (cardboard,
plastic tapes and styrofoam), so that in case of a problem,
the device can be sent back to the service centre in accurate
condition.
DISPOSING OF PACKAGING
The various items used for packaging (cardboard, plastic
straps, polyurethane foam) should be conserved, so that
the device can be sent back to the service center in best
conditions in case of problem!
INSTALLING THE APPLIANCE
Appliance location
The work surface where the device will be located must be
suitable for the size of the appliance, please refer to the
measure¬ments. The work surface must be levelled, dry,
heat-resistant and at a fitting height from the ground to
enable a proper use of the de¬vice.
The power cord connected with the appliance must be
properly grounded and correspond to the technical details.
Preparing for use
• Remove the device from the box and unwrap
protective films.
• Use knob (12) to extract saw blade with the splitting
wedge.
• Mount blade guard (6) by attaching it to the splitting
wedge (5) using a bolt in the guard.
Rev. 09.04.2020
6 19 5
• Place the push stick (18) on the bracket (17) on the
right side.
• Double check whether the saw blade (7) is correctly
mounted, there is no play and that it does not rub on
other saw elements by gently spinning it with your
hand. Make sure that the saw rotation direction is
in accordance with the rotation direction shown on
the saw blade.
• Always make sure that the saw blade and the
splitting wedge are in the same plane and that the
wedge edge is at the right distance (3-5 mm) away
from the saw blade teeth.
USE
1. Each and every time make sure the circular saw is
switched off. If the red "O" button is engaged – the
device is off, if the green "1" button is engaged – the
device is on.
LENGTHWISE CUTTING
a. Set the parallel guide (9) in the desired position on
the worktable. Ensure it is parallel to the saw blade
(7). Lock it in place using two bolts (10).
b. To use, push the workpiece against the guide (9) and
move it along the guide (9).
CUTTING AT AN ANGLE
a. Place the guide (3) in the groove (2). Loosen the
guide knob (4), set the required cutting angle,
tighten the knob.
b. To use, push the workpiece against the guide (3) and
move the guide along the groove (2).
c. For crosswise 45 degree cutting use the cross guide
in the circular saw accessories. Mount it in the
parallel guide (9).
CUTTING WITH CHAMFERING
a) Loosen the knob (13), set the tilt angle of the saw
blade (7), tighten the knob (7).
b) Cur according to the required cutting method, i.e.
lengthwise or crosswise.
2. Use knob (12) to set the height of the saw blade, or
cutting depth.
3. Connect the device to a power source, use button
(15) to turn on. Wait a few seconds for the blade
to achieve its maximum speed. Position wood
workpiece on the worktable and begin cutting.
OVERLOAD BREAKER
The circular saw has overload protection. If the user
overloads the circular saw, the breaker turns off the saw
motor. Follow these steps if that happens:
1. Wait at least a few minutes fort the device to cool
down.
2. Press button (14) to reset the overload breaker.
3. Press the green "1" button (15) to activate the
circular saw again.
Rev. 09.04.2020
REPLACING THE SAW BLADE
1. Remove blade guard (6) by reversing the steps for
assembling it.
2. Use knob (12) to retract saw blade with the splitting
wedge.
3. Unscrew and remove base insert (8).
8
4. Turn the device "upside down" and unscrew the base
element number 20 shown on the diagram below.
20
5. Unscrew guard (21) as shown below.
21
6. Use two spanners to unscrew the saw blade. Use one
to keep the shaft in place and the other to remove
the nut.
1
2
1 2
7. Mount the new saw blade, then the removed
elements in reverse order to their disassembly.
GENERAL COMMENTS
• After use, always turn off the circular saw by pressing
the red "0" button!
• Only use saw blades with parameters specified in the
user manual
• Do not use high speed steel (HS) saw blades!
• Move the wood slowly and steadily in the direction
of the saw blade rotation.
• Do not use blunt saw blades. This might result in
poor cut quality and the blade snagging.
• Make sure the blade guard is always lowered and the
splitting wedge is in place when sawing.
• Use the push stick for cutting narrow, small etc.
elements. When not using the push stick, place it in
the bracket.
• Secure long pieces of wood against falling off the
circular saw after cutting.
• If the blade snags during cutting, disconnect the
device from the power source and gently pull back
the workpiece.
9