DeWalt DXDP610100 Manual De Instrucciones página 4

Ocultar thumbs Ver también para DXDP610100:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
TECHNICAL SPECIFICATIONS TABLE
Category
Product Name
Tool Holder
Mobile Phone Holder
Tape Measure Holder
Tool Holder
Tool Anchor
Wristband Tool Anchor
Tool Anchor
Tool Anchor Strap
Tool Anchor
Tool Anchor Strap
Tool Attachment
Tool Tape
WARNING:
Tool lanyards or similar products are 
never to be used as Personal Protective Equipment 
(PPE).  Never use any tool lanyard or their 
subcomponents beyond their individual capacity 
rating.
WARNING:
 Do not use lanyard to support your 
body, work materials, or to secure any object 
other than a hand tool within specified weight-
ratings (Do not exceed 5 lb (2.26 kg) tool weight if 
anchoring to your body).
WARNING:
Dropped tools will swing on the 
lanyard, which could cause injury or loss of 
balance.
WARNING:
Do not alter or use in a manner other 
than as instructed in this manual.
4
Product Code
Rating
Length
Material
H 7" W 2.95" ( 18 x 7.5 cm.)
Polyester,Steel
DXDP610100
2 lbs
DXDP610200
2 lbs
H 5" W 3.74" (13 x 9.5 cm.)
Polyester,Steel
2 lbs
DXDP610300
H 1.97" W 4.72" (12 x 5 cm.)
Polyester,Steel
50 lbs
L 24" (60 cm.)
Polyester,Steel
DXDP813002
DXDP813012
80 lbs
L 24" (60 cm.)
Polyester,Steel
DXDP810100
N/A
L 12' W 1" (365 x 2.5 cm.)
Silicone
WARNING:
This product is not serviceable.
If damaged or not functioning properly, replace 
before resuming work.
WARNING:
Always select the proper tool 
lanyard or attachment for the job.  Ensure its 
rating matches or exceeds item being attached.
WARNING:
Inspect tool and lanyard before 
each use for damage and proper function 
(including fabric and stitching). Do not use if 
damaged or not functioning properly.
WARNING:
Do not attach more than one Tool
to each Lanyard (or lanyard leg).
TOOL LANYARDS
CAUTION:
On some occasions the tools a user has to 
carry for specific work at all heights do not come with built-
in or prescribed attachment options for the tool lanyard 
connection. The D
WALT range of tool attachments are the 
E
perfect solution for such cases and help provide a secure 
connection for the tool lanyard in the tethering system. 
Different tools will require different tethering system 
components depending on their shape and weight. Do not 
use the tethering system for pulling or towing objects.
Fundamental steps:
a )  Choosing the attachment point on the tool.
b )  Choosing the lanyard connector.
c )  Choosing the anchor point.
Choosing the attachment point on the tool:
a )  This may be a hole on the handle or on the body of the
tool. Alternatively, the body of the tool may serve as an
attachment point.
b )  If the above options are not available, the attachment
point may be created on the tool directly.
c )  Use only with tools that are specifically designed for 
D
WALT
tethering, or by using appropriate
attachment
E
accessories. NEVER modify tools to create attachment points.
Do not attach to a tool in a way that keeps guards, switches
or lock-offs from operating properly.
d )  Make sure the taping area of the tool is free of sharp edges.
SPECIFICATION OF THE TAPE:
Yellow in Color
Roll is 1" wide by 12' long
( 2.54 cm by 365.75 cm)
TOOL TAPE DXDP810100
English
WARNING:
The tape layers will start to self-merge 
immediately with permanent adhesion within 24 hours.
Repositioning is not recommended. Even though the 
silicon tape may be used under wet or oily conditions, 
an application on a clean, dry surface is recommended. 
The tape is not reusable, but additional tape layers can 
be added at any point in time. After application and 
curing time, always check the strength of the application 
by testing it with a 3 lbs./1.36 kg. load. Perform this test 
before every use.
a )  Clean the surface to be used and cut a piece of the tape
to the desired length (i.e. from one point to another it should
have at least 10 loops for proper grip). The length should be
adjusted based on the size of the tool/handle.
b )  Make the 1st winding around the handle holding the 
tape in position and rolling it around the desired part
(handle + attachment D-ring) until the tape is doubled over
itself. This initial winding tape on tape will help to secure the
future layers.
c )  Ensure that constant tension is maintained as
subsequent layers of tape are applied and that each new layer
partially covers both the bare part and the prior layer of tape.
This overlapping will help the tape to self-merge. The stretch
should be 40 to 50% of the remaining length of the tape; this
stretching ensures the application will hold.
d )  The tape must be wound at minimum over the entire 
length of the attachment D-ring in one direction and
covered a second time over itself in the other direction. The
last layer of tape must be wound completely over the previous
layer without overlapping. Maximum tension is not 
necessary on the last layer.
e )  Do not flex the tape too much as it may break.
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dxdp610200Dxdp610300Dxdp813002Dxdp813012Dxdp810100Dxdp711100

Tabla de contenido