Trixie TX9 Smart Instrucciones De Uso página 6

EZ mode and AP mode. EZ mode works exclusively in pure 2.4
GHz networks. The AP mode, on the other hand, also works with
modern dual-band routers that broadcast 2.4 GHz and 5.0 GHz in
parallel. We recommend pairing in AP mode.
4. Please note that the feeder will not work in 5.0 GHz-only networks.
5. If your WLAN password contains special characters, there may be
problems with the pairing process. Change your WLAN password so
that it contains only letters and numbers. The maximum length of
the WLAN password is 20 characters.
AP mode (recommended)
1. Reset the feeder by pressing and holding the SET button on the
bottom of the unit for 5+ seconds. An audible signal will sound to
confirm and after about half a minute the green indicator light above
the camera should begin to flash rapidly. (Approx. 1 time per second)
Note: Please contact customer service(smartsupport@trixie.de) if
you do not hear a beep and the green indicator light does not start
flashing after the reset.
2. Now press the SET button 11 times in quick succession to activate
the hotspot for pairing in AP mode. An acoustic signal confirms the
activation and after about half a minute the green indicator light
should start to flash slowly. (Approximately 1 time every 3 seconds)
If the indicator light continues to flash rapidly, the hotspot activation
did not work properly. In this case, repeat this step. Please make sure
to press the SET button quickly and evenly!
3. In the app, select ADD DEVICE, and then select SECURITY CAMERA
(Wi-Fi) in the VIDEO MONITORING device category.
4. On the following page, select Wi-Fi MODE from the drop-down
menu in the upper right corner. Tap NEXT and select the AP MODE.
Note: The default pairing method „QR code" does not work with TX
Smart feeders.
5. Enter your WLAN access data on the following page. Tap NEXT.
Please note that the WLAN password must not contain any special
characters.
6. Tap CONNECT NOW and select the hotspot of the automatic feeder
from the list of available WLAN networks: SmartLife_XXXX.
Please note that in some cases it may take a while for the phone to
find the hotspot. If the hotspot does not appear in the list at first,
just wait for a few more seconds.
1. Please note that in some cases it may take a while for the phone to
find the hotspot. If the hotspot does not appear in the list at first,
just wait for a few more seconds.
2. The app will start the pairing process and should connect to the
feeder after a short wait.
3. Tap FINISH to go to the feeder's user interface.
EZ Mode (2.4 GHz only)
1. Reset the feeder by pressing and holding the SET button on the
bottom of the unit for 5+ seconds. An audible signal will sound to
confirm and after about half a minute, the green indicator light
above the camera should begin to flash rapidly. (Approx. 1 time per
second)
Note: Please contact customer service(smartsupport@trixie.de) if
you do not hear a beep and the green indicator light does not start
flashing after the reset.
2. In the app, select ADD DEVICE and then select SECURITY CAMERA
(Wi-Fi) in the VIDEO MONITORING device category.
3. On the following page, select Wi-Fi MODE from the drop-down
6
menu in the upper right corner. Tap NEXT and select EZ MODE.
Note: The default pairing method „QR code" does not work with TX
Smart feeders.
4. Enter your WLAN access data on the following page. Tap NEXT.
Please note that the WLAN password must not contain any special
characters.
5. The app will start the pairing process and should connect to the
feeder after a short wait.
Pairing again
Please proceed as follows if you need to pair the automatic feeder
again - e.g. after moving house or assigning a new WLAN password.
Open the Tuya App home page and give a long tap on the Pet Feeder
icon to remove the device from the app. Caution - all programmed
feeding times will be lost. After that, wait for about one minute until
the green indicator light on the front of the device starts blinking
again. You can then repeat the pairing process in AP or EZ mode.
Sharing the feeder:
Follow these steps to give another person access to your feeder:
1. Tap the pencil icon in the upper right corner to enter the feeder menu.
2. Tap SHARE DEVICE > ADD SHARING, and then tap SHARE WITH
TUYA SMART ACCOUNT. Under ACCOUNT, now enter the email
address that the other person previously registered with Tuya. Please
note that the person you share the machine with in this way will have
full access to the machine - including the camera and microphone.
Note: It is also possible to log into the same Tuya account from
multiple devices. This is especially useful if you want to control the
automatic feeder yourself from different mobile devices (e.g. smart-
phone + tablet).
Filling the feeder
After successful pairing, you can fill the feeder with dry food. Place
the lid on the food bowl and turn it to close it securely. Open the
bowl by pressing against it and then pulling it out. Then trigger a
manual feeding by briefly pressing the SET button of the device once.
This will ensure that the feeding mechanism of the machine is also
filled with food.
The dry feed used should not exceed a maximum diameter of 15 mm.
A circular shape is preferable. Dry feed that is too flat, too large, unu-
sually shaped or very sticky can promote a blockage in the conveying
mechanism.
Please make sure that the food slides down properly in the bowl.
When in doubt, switch to a less sticky type of food if the food accu-
mulates in the top half of the bowl and blocks the outlet.
Programming the Feeding
Click on SCHEDULED FEEDING and ADD FEEDING TIME to set fee-
ding times. Here you can set different times for feedings and the days
on which they should be repeated, if necessary. You can also set the
amount of portions dispensed for feeding (1 portion= approx. 12 ml).
In the overview of the feeding times you can easily activate or deacti-
vate individual feeding times.
Manual feeding
• Press FEEDING and select the number of portions to be dispensed
immediately.
• Press LOCKCALL to record a 10 second voice memo. This will be