Description Of Symbols; General Safety - Silverline 264782 Manual

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Class I construction (Protective earth)
Conforms to relevant legislation and safety standards
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice
Specification
Voltage: .............................................. 230V~
Frequency: ......................................... 50Hz
Power: ............................................... 500W
Maximum loading capacity: ............... 250kg
Maximum lifting capacity: .................. 250kg with return pulley
Maximum lifting heights: ................... 6m with return pulley (250kg)
Average lifting speed: ........................ 4m/min with return pulley (250kg)
Protection Class: ................................
As part of our ongoing product development, specifications of Silverline
products may alter without notice.
4
All manuals and user guides at all-guides.com
125kg without return pulley
12m without return pulley (125kg)
8m/min without return pulley (125kg)
Carefully read and understand this manual and any label attached to
the tool before use. Keep these instructions with the product for future
reference. Ensure all persons who use this product are fully acquainted
with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.

General Safety

Clean the work area
• Accidents can occur where benches and work areas are cluttered or
dirty. Keep floors clear and avoid working where the floor is slippery. If
working outdoors, be aware of all potential slip and trip hazards before
using this tool
Children and pets
• Keep children and pets at a safe distance from the work area. Lock tools
away where children cannot gain access
Trained, competent persons
• This tool should be used by trained, competent persons only
Wear suitable clothing and footwear
• Do not wear loose fitting clothing, neckties, jewellery, or other
items which may become caught. Wear non-slip footwear or, where
appropriate, footwear with protective toe caps. Long hair should be
covered or tied back
Protective equipment
• Refer to the rating plate on your tool for information relating to the
necessary protective equipment when using this product. Example; dust
mask/respirator, goggles, ear defenders, gloves etc
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing.
Carefully check that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre. DO NOT USE IF DEFECTIVE
Use the correct tool
• Do not force or attempt to use a tool for a purpose for which it was not
designed. This tool is not intended for industrial use
Accessories
• The use of any attachment or accessory, other than those mentioned in
this manual, could be dangerous and result in damage or injury, and may
invalidate your warranty
Keep guards in position
• Where guards exist keep them in position, in good working order,
correctly adjusted and aligned. Never attempt to use a tool if any of
the supplied guards are missing. If any guards are damaged, replace
before use
Remove adjusting keys
• Where adjusting keys exist, ensure they are removed prior to using the
tool. Always check to see that keys and adjusting devices are removed
from the tool before use
Secure work
• Where possible, always secure work. If appropriate, use a clamp or vice
so that both hands are free to operate the tool
Keep your balance
• Do not over-reach. Keep secure footing at all times and do not use tools
when standing on an unstable surface
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool
is tipped or collapses. Do not store materials above or close to the tool
in such a way that a person might stand on the tool to reach the stored
items