Standard Accessories - HIKOKI G 1812DA Instrucciones De Manejo

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 63
English
min
Revolution or reciprocations per minute
-1
D
Wheel outer diameter
d
Wheel hole diameter
t
Wheel thickness
Peripheral speed
Weight*
(According to EPTA-Procedure 01/2014)
kg
Switching ON
Switching OFF
Disconnect the battery
Warning
*
Depending on attached battery. The heaviest weight is
measured with BSL36B18 (sold separately).
Also, the weight includes the wheel guard, side handle,
wheel washer, and wheel nut.
Battery
Lights ;
The battery remaining power is over 75%
Lights ;
The battery remaining power is 50%–75%.
Lights ;
The battery remaining power is 25%–50%.
Lights ;
The battery remaining power is less than 25%
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to
fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please
contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed on page 248.
Standard accessories are subject to change without notice.
APPLICATIONS
○ Removal of casting fi n and fi nishing of various types of
steel, bronze and aluminum materials and castings.
○ Grinding of welded sections or sections cut by means of
a cutting torch.
○ Grinding of synthetic resins, slate, brick, marble, etc.
SPECIFICATIONS
1. Power tool
The specifi cations of this machine are listed in the Table on
page 246.
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
Electronic control
○ Soft start
Reduces recoil against the operator by managing the
number of rotations during startup.
○ Kickback Protection
The kickback protection feature cuts off the power to
the motor and stops the power tool in the event of a
sudden drop in the rotational speed of the wheel during
operation (for example, if the wheel locks during cutting
operation, etc.).
○ Overload protection
This protection feature cuts off the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
○ Overheat protection
This protection feature cuts off the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Restart prevention function
When the power is still switched on, the tool will not
restart when a battery is installed. This function can be
canceled once the tool is switched off .
2. Battery
Model
Voltage
Battery capacity
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (At 1- second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 4 (on page 2).
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
12
BSL1850MA
18 V
5.0 Ah

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

G 1813da

Tabla de contenido