DeWalt DW712 Manual De Instrucciones página 33

• Set your saw to the prescribed angles and make a few trial cuts.
• Practice fitting the cut pieces together.
• Example: To make a 4 sided box with 25° exterior angles (angle "A")
(fig. S2), use the upper right arc. Find 25° on the arc scale. Follow the
horizontal intersecting line to either side to get the mitre angle setting
on the saw (23°).
Likewise follow the vertical intersecting line to the top or bottom to get
the bevel angle setting on the saw (40°). Always try cuts on a few scrap
pieces of wood to verify the settings on the saw.
Cutting base mouldings
The cutting of base moulding is performed at a 45° bevel angle.
• Always make a dry run without power before making any cuts.
• All cuts are made with the back of the moulding laying flat on the saw.
Inside corner
- Left side
• Position the moulding with top of the moulding against the fence.
• Save the left side of the cut.
- Right side
• Position the moulding with the bottom of the moulding against the
fence.
• Save the left side of the cut.
Outside corner
- Left side
• Position the moulding with the bottom of the moulding against the
fence.
• Save the right side of the cut.
- Right side
• Position the moulding with top of the moulding against the fence.
• Save the right side of the cut.
Cutting crown mouldings
The cutting of crown moulding is performed in a compound mitre. In order
to achieve extreme accuracy, your saw has pre-set angle positions at
31.62° mitre and 33.85° bevel. These settings are for standard crown
mouldings with 52° angles at the top and 38° angles at the bottom.
6 SIDED BOX
8 SIDED BOX
SET THIS BEVEL ANGLE ON SAW
All manuals and user guides at all-guides.com
• Make test cuts using scrap material before doing the final cuts.
• All cuts are made in a left bevel and with the back of the moulding
Inside corner
- Left side
- Right side
Outside corner
- Left side
- Right side
Grooving (fig. T)
Your saw is equipped with a grooving stop (12) and thumbscrew (15) to
allow for groove cutting.
• Flip the grooving stop (12) towards the front of the saw.
• Adjust the thumbscrew (15) to set the depth of the groove cut. It might
• Place a piece of scrap material of approx. 5 cm between fence and
Dust extraction (fig. A2 & A6)
This machine is provided with a dust extraction point (24) for connection of
a dust extraction kit (37) (available as an option).
• Whenever possible, connect a dust extraction device designed in
Cutting small pieces (fig. A5)
The fence insert (36) (available as an option) will increase the ease of
cutting small pieces.
Support for long pieces (fig. A4)
• Always support long pieces.
SQUARE BOX
• For best results, use the extension work support (35) to extend the
Saw blades
To obtain the stated cutting capacities, always use 216 mm saw blades
with 30 mm arbor holes.
Consult your dealer for further information on the appropriate accessories.
against the base.
• Top of the moulding against the fence.
• Mitre right.
• Save the left side of the cut.
• Bottom of the moulding against the fence.
• Mitre left.
• Save the left side of the cut.
• Bottom of the moulding against the fence.
• Mitre left.
• Save the right side of the cut.
• Top of the moulding against the fence.
• Mitre right.
• Save the right side of the cut.
be necessary to release the lock nut (66) first.
workpiece in order to perform a straight groove cut.
accordance with the relevant regulations regarding dust emission.
table width of your saw (available from your dealer as an option).
Support long workpieces using any convenient means such as saw-
horses or similar devices to keep the ends from dropping.
E N G L I S H
33