Error Messages - Beninca SAM Serie Manual Del Usuario

The list is displayed of some messages which are shown on the display in the event of an operating anomaly:
Amp1 Motor 1 obstacle error/anti-crushing
Amp2 Motor 2 obstacle error/anti-crushing
Encoder 1 error/obstacle detection
ENC1
ENC2 Encoder 2 error/obstacle detection
ERR AUTOSET error
Err1 Motor 1 circuit test error
Err2 Motor 2 circuit check error
PHOTA photocell test error
Err4
Err5 PHOTC photocell test error
Err8 Inputs enabling error
BAR BAR input intervention (sensitive edge)
Motor thermal switch safety device interven-
thrm
tion
ovd1 Overload M1
ovd2 Overload M2
The following table is used to record maintenance operations, improvement or repair works carried out by the expert engineer.
Date _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Description of operation
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Date _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Description of operation
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Date _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Description of operation
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Date _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Description of operation
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

ERROR MESSAGES

Check the presence of obstacles on the stroke of the motor gate 1
Check the presence of obstacles on the stroke of the motor gate 2
Check correct connection of the encoder of motor 1 to the control panel,
the presence of obstacles on the stroke of the gate and correct operation
of the encoder.
Check correct connection of the encoder of motor 2 to the control panel,
the presence of obstacles on the stroke of the gate and correct operation
of the encoder.
Repeat autoset procedure
Check motor 1 connections. Motor disconnected or not working. Problem
on control panel
Check motor 2 connections. Motor disconnected or not working. Problem
on control panel
Check connections, alignment of the photocell PHOT OP or obstacles
present.
Check connections, alignment of the photocell PHOT LC or obstacles
present.
During the autoset phase, an input activated (START/PP/Open/Close/PED)
or one of the buttons (+/-/PG) activated. Repeat the autoset procedure.
During the manoeuvre, the sensitive edge detected an obstacle.
Overheating due to permanent obstacles. Release the gate and check
there are no friction points.
Maximum power exceeded. Check motor or presence of friction.
Maximum power exceeded. Check motor or presence of friction.
MAINTENANCE
Engineer's Signature _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Engineer's Signature _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Engineer's Signature _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Engineer's Signature _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
EN
Stamp
Stamp
Stamp
Stamp
35