VONROC EH515AC Traducción Del Manual Original página 7

- Eco mode: the eco mode indicator (8A) will
light up. The indicator light (3) will flash red
slowly.
- Fan: The fan indicator (8E) will light up. The
indicator light (3) will turn blue.
- Low heating mode – 1000W: the low heating
indicator (8C) will light up. The indicator light
(3) will turn purple.
- High heating mode – 2000W: the high heating
indicator (8B) will light up. The indicator light
(3) will turn red.
- Oscillation button (12): Press the oscillation
button to activate the heater to swing. Press it
again to deactivate.
- Timer button (13): The timer can be set
between 1 hour and 9 hours. The display will
show the duration currently set. Press the
timer button (13) to set the timer with 1 hour
intervals. The timer button will light up. Without
a timer there is no limit.
Control panel lock (Fig. B)
Hold the timer / lock button (16) for 3 seconds. The
lock indicator (8F) will light up. The heater will be
locked and can't be operated anymore. To release the
lock, press the timer / lock button (16) for 3 seconds.
Eco mode (Fig. B)
Press the mode button (11) to select eco mode.
The eco mode indicator (8A) will light up. The indi-
cator light (3) will flash red slowly. The heater will
heating in cycle High Heat-Low Heat to maintain
the room temperature around 24
turn off automatically if there is no operation within
24 hours continuous working.
Functions of the remote control (Fig. C)
In addition to the before mentioned control panel
operation, the heater can also be operated by the
remote control(14). The available functions are:
- Temperature increase button (17): Press to
increase the desired ambient temperature.
- Temperature decrease button (18): Press to
decrease the desires ambient temperature.
- Heater on/off button (15): Turns the heater on
and off.
- Mode button (11): Cycles between eco mode,
low and high heating.
- Eco mode: The eco mode indicator (8A) will
light up. The indicator light (3) will flash red
slowly.
WWW.VONROC.COM
- Fan: The fan indicator (8E) will light up. The
- Low heating mode – 1000W: The low heating
- High heating mode – 2000W: The high heating
- Oscillation button (12): Press the oscillation
button to activate the heater to swing. Press it
again to deactivate.
- Timer button (19): The timer can be set bet-
ween 1 hour and 9 hours. The display will show
the duration currently set. Press the timer but-
ton (19) to set the timer with 1 hour intervals.
The timer button will light up. Without a timer
there is no limit.
- Light on/off button: Cycles between turn off
the control panel light (2), turn off the indicator
light (3) and turn on both.
Tip-over switch
This heater has an digital tip-over protection. This
protection ensures when the heater is not placed
upright on a firm and level surface or when the
heater tip over, the system will automatically shut
the heater off. If this occurs, put the heater on a
firm and level surface and start the heater again.
Automatic Overheat Safety Control
This heater is equipped with safety internal heat
limiting thermostat and overheat protection circuit.
C. The heater will When a potential overheat temperature is reached,
o
the system will automatically shut the heater off.
If this occurs, the heater can only resume after
resetting it. To reset the heater: Unplug the heater
and wait at least 30 minutes to cool down before
restarting the heater.
Stopping the electric heater (Fig. B, C)
• Press the on/off button (10, 15).
• The fan mode will start and will cool down the
heater for 15 seconds. The display will show the
duration.
• Pull the plug out of the mains power outlet.
indicator light (3) will turn blue.
indicator (8C) will light up. The indicator light
(3) will turn purple.
indicator (8B) will light up. The indicator (3)
will turn red.
Let the machine cool down before turning
off by using the ventilation function.
EN
7