Publicidad
GENERAL INSTRUCTIONS.-
Read the instructions in this manual. This gives important
information on the safety, use and maintenance of the
machine.
Follow the following recommendations:
1
Keep children and animals away from the machine. Do
not leave children unsupervised around the equipment.
2
The machine will only be used by 4 people at the same
time.
3
Work at the recommended exercise level, do not get to
exhaustion. If you feel pain or discomfort of any kind, stop
exercising immediately and consult your doctor.
4
Use the appliance on a solid, level surface with 1 meter
around. It is not advisable to keep your unit in wet place
because the oxidation would be inevitable. Do not use the
equipment outdoors.
5
Keep hands and feet away from moving parts.
6
Use suitable clothing and footwear. Tighten the laces
properly.
7
Use the equipment according to the functions described
in the manual, do not use accessories or exercises other
than those described by the manufacturer.
8
Do not place any sharp objects around the machine.
9
Do not allow children or disabled persons use the
appliance without the strict supervision of a qualified
person.
10
Do stretches before using the computer as a warmup.
11
Select an appropriate weight to their physical condition.
12
Do not use the equipment if it is damaged or
incomplete.
13
It is recommended to exercise a monitor to oversee the
exercise.
14
This unit has been designed for home use. The
maximum user weight is 130 kg.
Caution: Consult your doctor before beginning to use
the machine. This advice is especially important for
those over 35 or suffering from health problems.
Keep these instructions safe for future use.
MAINTENANCE.-
1 Lubricate moving parts regularly. At least once a year.
2 Check that all parts are tight and that the machine is
working properly before first use.
3 Use a damp cloth to clean the equipment. The use of
solvents is not recommended.
English
ASSEMBLY INSTRUCTIONS.-
Take the unit out of its box and make sure that all of the
pieces are there, Fig.A, Fig.B.
The assistance of a second person is required for
assembling this machine.
1.- Attach the stand post (12) to the base frame (1) and fix
it using the screws (112) and the washers (11), Fig.1.
2.- Attach the columns (23) to the base frame (1) and fix
them using the screws (111) and the washers (123), (11),
Fig.2.
3.- Place the upper frame (20) on the columns (23), fix it
using the screws (111) and the washers (123), (11), Fig.3.
Do not tighten completely.
Attach the upper frame (20) to the vertical frame (12)
using the screws (112) and the washers (11), Fig.3.
Tighten all the screws.
4.- Place the frame (66) on the base frame (1) and fit the
screws (9), the washers (11) and the nuts (10), Fig.4. Do
not tighten completely.
Attach the frame (66) to the stand post (12) using the
screws (112) and the washers (11), Fig.4.
Tighten all the screws.
5.- Attach the arm assembly (88) and fix it to the stand
post (12) using the screws (74) and the washers (75),
Fig.5.
6.- Attach the back frame (21) and fix it to the vertical
frame (12) using the screws (120) and the washers (11),
Fig.6.
7.- Place the support (96) on the upper structure (20) and
attach it using the nut (97), the screws (74) and the
washers (75), Fig.7.
8.- Place the guide rods (24) at points (a) and (b), Fig.8.
Insert the bushing (30), the cushion (31), the weights (27),
and the top weight (26).
Insert the selector pin (28) into the rod (29) (the other side
of the selector pin is placed on the cable (39)), Fig.8.
Align the guide bars (24) with the upper frame (20) and fix
them with the screws (108) and the washers (11), Fig.8.
9.- Place the seat pad (64) on the support (60) and fit the
screws (114), Fig.9.
Insert the support (60) into the bushing (68), pull the knob
(69) out, adjust the position of the seat (64) and release
the knob (69) to fix the position, Fig.9.
10.- Place the foam tubes (59) as shown in Fig.10, place
the inner covers (63), the foams (61), the outer covers
(62) and fit the screws (115).
11.- Place the foam tubes (58) as shown in Fig.11, place
the inner covers (63), the foams (61), the outer covers
(62) and fit the screws (115).
12.- Attach the butterfly assembly (76) to the support (96)
aligning with point (c), remove the knob (18), adjust the
18
Publicidad
