Gaggenau AR410110 Instrucciones De Montaje página 8

WARNING ‒ Risk of suffocation!
Children may put packaging material over their
heads or wrap themselves up in it and suffocate.
Keep packaging material away from children.
▶
Do not let children play with packaging material.
▶
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appli-
ance from the electricity supply. The appliance must
only be connected to a protective contact socket
that has been correctly installed.
The mains plug for the mains power cable must
▶
be easily accessible after the appliance is in-
stalled.
If this is not possible, an all-pole isolating switch
▶
must be integrated into the permanent electrical
installation according to the conditions of over-
voltage category III and according to the installa-
tion regulations.
The permanent electrical installation must only be
▶
wired by a professional electrician. We recom-
mend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
WARNING ‒ Risk of injury!
Changes to the electrical or mechanical assembly
are dangerous and may lead to malfunctions.
Do not make any changes to the electrical or
▶
mechanical assembly.
Components inside the appliance may have sharp
edges.
Wear protective gloves.
▶
Scope of delivery
After unpacking all parts, check for any damage in
transit and completeness of the delivery.
→ Fig.
1
Appliance dimensions
You will find the dimensions of the appliance here
→ Fig.
2
Installation examples
This is where you can find possible installation ex-
amples.
→ Fig. , → Fig.
3 4
Information about the electrical
connection
In order to safely connect the appliance to the elec-
trical system, follow these instructions.
WARNING ‒ Risk of electric shock!
Sharp-edged components inside the appliance may
damage the connecting cable.
Do not kink or trap the connecting cable.
▶
The connection data can be found on the rating
¡
plate.
This appliance complies with the EC interference
¡
suppression regulations.
The appliance corresponds to protection class 1.
¡
You should therefore only use the appliance with
a protective earth connection.
Do not connect the appliance to the power supply
¡
during installation.
General information
Follow these general instructions during the installa-
tion.
The currently valid building regulations and the regu-
lations of the local electricity and gas suppliers must
be observed during installation.
8
Installation
Checking the unit
Check whether the fitted unit is level and has suffi-
▶
cient load-bearing capacity.
Preparing the unit
Mark the unit cut-out in accordance with the in-
1.
stallation diagram
→ Fig.
5
Establish a cut-out in the bottom plate.
2.
Ensure that the angle of the cut surface to the
‒
worktop is 90°.
Make an air outlet in the plinth on the unit.
3.
Provide a minimum air outlet cross-section of
‒
approx. 400 cm².
Make the outlet opening in the base panel as
‒
large as possible in order to keep draughts and
noise to a minimum.
Ensure that the fitted unit is still stable after the
4.
cut-outs have been made.
Seal the cut surfaces so that they are heat-resist-
5.
ant and waterproof.
→ Fig.
6
Remove any shavings.
6.
Preparing the appliance
For a base height greater than 80 mm, ensure
▶
that the access to the filters is guaranteed.
→ Fig.
7
Installing the bracket on the appliance
Install the enclosed bracket on the side of the ap-
▶
pliance.
→ Fig.
8
Installing the appliance under a unit
Requirement: It is not possible to install the bracket.
Install the appliance under the unit.
▶
→ Fig.
9
Installing the appliance
Insert the appliance into the cut-out.
1.
→ Fig.
10
The appliance has rubber feet. It is not necessary
to secure it to the ground.
Align the appliance horizontally.
2.
Unpack and insert the odour filter.
3.
→ Fig.
11
Screw in the filter covers.
4.
→ Fig.
12
Install the connecting piece on the appliance.
5.
Affix the seal on the connecting piece.
6.
→ Fig.
13
Lay the piping to the downdraft ventilation and
7.
seal it appropriately.
Secure the exhaust air pipe to the connecting
8.
piece and seal it appropriately.
Connecting the appliance
WARNING ‒ Risk of electric shock!
If the insulation of the power cord is damaged, this is
dangerous.
Never let the power cord come into contact with
▶
hot appliance parts or heat sources.
Never let the power cord come into contact with
▶
sharp points or edges.
Never kink, crush or modify the power cord.
▶
Use the control cable to connect the remote fan
1.
unit and the fan.
→ Fig.
14