Manuales relacionados para Truper MAX-20SC
Resumen de contenidos para Truper MAX-20SC
- Página 1 Manual Cordless 6-1/2” Circular Saw Disc Applies for: Code Model 102480 MAX-20SC MAX-20SC Read this manual thoroughly CAUTION before using the tool.
-
Página 2: Tabla De Contenido
Manual before Parts using the tool. Preparation Keep this manual for future references. Start up The illustrations in this manual are for reference Maintenance only. They might be different from the real tool. Notes Authorized Service Centers Warranty Policy MAX-20SC... -
Página 3: Technical Data
Technical Data MAX-20SC Code 102480 Description Cordless circular saw Disc 6-1/2” Maximum a 90º: 2 1/8” | a 45º: 1 1/2” cutting depth Voltage 20 V Speed 4 200 RPM IP Grade IP20 Battery Ion-lithium 20 V 4 Ah | Charging time: 80 min approximately... -
Página 4: General Power Tools Safety Warnings
General power tools safety warnings WARNING! Read carefully all safety warnings and instruction listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references. -
Página 5: Safety Rules For The Use Of Circular Saws
Kickback Kickback refers to the sudden, forceful movement of the DANGER • Use only Truper Max chargers to charge tool away from the workpiece that can cause the operator the tool battery. Using any other charger may result in fire to lose control or even cause injury. -
Página 6: General Warnings
Safety rules for the use of circular saws Retractable guard It also increases the likelihood that the cut will close and • Before each use check the retractable guard and its the available area above the disc will increase. spring for proper operation, if the guard does not move •... -
Página 7: Parts
Allen ejection of the sawdust. Dust nozzle LED light Charger Retractable guard control lever Base TRUPER ST-624 6-1/2” tungsten carbide cut-off disc Retractable Outer flange guard Switch Switch lock button Charge Battery indicators Handle... -
Página 8: Preparation
Preparation Battery charging 1. Plug the charger plug into a 127 V~ socket. The green light of the charging indicator will turn on. 2. Insert the battery into the charger by sliding it as shown in the picture. The green light will turn off and the red light should turn on, indicating that charging has started. -
Página 9: Start Up
Preparation Dust nozzle assembly • Take the dust nozzle (A) and place it on the inside of the sawdust ejector (B). • Rotate the nozzle to the preferred direction to dislodge the sawdust. Start up The circular saw is a multi-purpose tool for cutting soft or hard wood, chipboard, plywood, resopal-coated materials, etc. CAUTION This tool is not designed for cutting metal, masonry, concrete or brick materials. -
Página 10: Cutting Angle Adjustment
Start up Cutting angle adjustment • Loosen the cutting angle adjustment knobs (D). • With the base stationary, rotate the housing until the blade is at the desired angle. • Tighten the cutting angle adjustment knobs to prevent the housing from moving during cutting. •... -
Página 11: Maintenance
Maintenance Change of the cut-off disc Once the cut-off disc wears out, they should be replaced immediately. WARNING The cut-off disc specified for this tool are 6-1/2”. Do not use any other size. Failure to do so may result in an accident or damage to the tool and void your warranty. -
Página 12: Notes
Notes ENGLISH... -
Página 13: Authorized Service Centers
In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. DE TODO PARA LA CONSTRUCCIÓN FIX FERRETERÍAS... -
Página 14: Warranty Policy
Phone number 800-018-7873. Made in China. Imported by Truper, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761 782 9100.