Storage Recommendations - Black and Decker BCN115 Traducido De Las Instrucciones Originales

ENGLISH
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool
is switched off or when it is running but not actually doing the
job.
Important safety instructions for all integral battery
tools
Warning! Read all safety warnings, instructions, and
cautionary markings for the battery, charger and product.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Never force a charger plug into the tool.
u
DO NOT modify the charger plug of a non‑compatible
u
charger in any way to fit into the tool as the battery may
rupture causing serious personal injury.
DO NOT charge or use the battery in explosive
u
atmospheres, such as in the presence of flammable
liquids, gases or dust.
Inserting or removing the charger plug from the tool may
ignite the dust or fumes.
Only charge the battery with the provided charge lead and
u
a suitable class 2 power supply.
DO NOT splash or immerse in water.
u
DO NOT allow water or any liquid to enter tool.
u
DO NOT store or use the tool in locations where the
u
temperature may reach or exceed 104 °F (40 °C) (such as
outside sheds or metal buildings in summer). For best life
store tools in a cool, dry location.
Do not store the tool with the switch locked on. Never tape
u
the switch in the ON position.
DO NOT incinerate the tool even if it is severely damaged
u
or is completely worn out. The battery can explode
in a fire. Toxic fumes and materials are created when
lithium-ion batteries are burned.
If battery contents come into contact with the skin,
u
immediately wash area with mild soap and water. If battery
liquid gets into the eye, rinse water over the open eye for
15 minutes or until irritation ceases. If medical attention is
needed, the battery electrolyte is composed of a mixture
of liquid organic carbonates and lithium salts.
Contents of opened battery cells may cause respiratory
u
irritation. Provide fresh air. If symptoms persist, seek
medical attention.
Battery liquid may be flammable if exposed to spark or
u
flame.
Never attempt to open the tool for any reason.
u
If the tool case is cracked or damaged, do not charge. Do
not crush, drop or damage the tool.
Do not use a tool or charger that has received a sharp
blow, been dropped, run over or damaged in any way
(e.g., pierced with a nail, hit with a hammer, stepped on).
6
(Original instructions)
Damaged tools should be returned to the service center
for recycling.

Storage recommendations

The best storage place is one that is cool and dry, away from
direct sunlight and excess heat or cold.
Store the fully charged tool disconnected from the charger.
Transportation
Note: Integral Li-ion tools should not be put in checked
baggage on airplanes and must be properly protected from
short circuits if they are in carry-on baggage.
Important safety instructions for all integral battery
charging
Warning! Read all safety warnings, instructions, and
cautionary markings for the battery, charging cable and
product. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Use only with the Listed/Certified Information Technology
u
(computer) Equipment.
DO NOT expose charging cable to water, rain or snow.
u
Pull by the plugs rather than the cord when disconnecting
u
the charging cable. This will reduce the risk of damage to
the plugs and cord.
Make sure that the cord is located so that it will not
u
be stepped on, tripped over or otherwise subjected to
damage or stress.
When charging the tool outdoors, always provide a dry
u
location.
DO NOT use a charging cable with a damaged cord or
u
plugs. Have them replaced immediately.
Foreign materials of a conductive nature, such as, but not
u
limited to, grinding dust, metal chips, steel wool, aluminum
foil or any buildup of metallic particles should be kept
away from the charging and micro charging plugs and
port.
Always unplug the charging cable from the power supply
u
when there is no tool attached to it.
Features
This appliance includes some or all of the following features:
1. Trigger
2. Power switch
3. Charge indicator/ready to use LED
4. Contact trip
5. Magazine
6. Magazine release clip
7. Stapler viewing window
8. Charge port
9. Charge lead