First Use; Optional Functions - Whirlpool 6th sense Guía De Consulta Rápida

FIRST USE

Connect the appliance to the power
supply (refer to the Installation
manual).When connecting the appliance
to the power supply, the display will show
the temperatures preset by the
manufacturer.(-18°C and +5°C).If the
temperature indicator appears,
accompanied by the acoustic alarm
(which means that the long black-out
alarm has been activated), press the
alarm reset button. Note: after switching
the appliance on, it will be necessary to
wait for 2 to 3 hours before a
temperature suitable for a standard
appliance load is reached.
Freezer
temperature
Refrigerator
temperature
OPERATION SYMBOLS
6th Sense
Function
Antibacterial filter
Freezer door anti-
condensation device
(stainless steel model with
rounded doors only)

OPTIONAL FUNCTIONS

Fast freezing
Control panel lock
function (Child
lock)
Vacation mode
Eco Mode
ALARMS
Black-out alarm
Door open alarm
Operation alarm
USE
To change the temperature press the Freezer temp. button until the display shows the required value.
To change the temperature press the Fridge temp. button until the display shows the required value.
The icon on indicates that the appliance is in the process of reaching the optimum preservation conditions.
This function activates and deactivates automatically.
This symbol shows the condition of the antibacterial filter. When receiving the appliance the icon will be on by
default. When the icon start flashing the filter needs to be replaced: replace the cartridge and press the Reset
filter/alarm until the icon stops flashing.
00800-40088400 - www.whirlpool.eu/myfridge
If you notice condensation on the freezer door press simultaneously the buttons Fast freezing e Reset
filter/alarm for about 3 seconds, until you hear an acoustic signal. To deactivate the function repeat the
function until you hear 3 short acoustic signals.
This function must be activated before freezing fresh food in the freezer compartment
To activate the function press the Fast freezing button until the fast freezing symbol
the display. The function will automatically deactivate after 24 hours or manually by pressing again the button.
To activate the function press the Child lock button (the
activated). To deactivate the function press the child lock button again.
This function deactivates the refrigerator compartment if the user is going away for sometime. This function is
activated/deactivated by pressing the Vacation mode button until the vacation symbol appears/disappears
After activating the function, remove perishable food from the refrigerator compartment and keep the door
closed, since the refrigerator maintains an adequate temperature for preventing the formation or odors.
This optional function can be used to save energy.
It is important to remember that this function does not disconnect the appliance from the power supply. To
activate it press the Reset filter/alarm and Child lock buttons simultaneously for approximately 5 seconds
until the display goes off completely and the icon
Whenever the appliance or the control panel is used the display will light on and will go off again, with the ECO
icon remaining visible.
To reinstate normal operating condition repeat the same operation until the display shows the previously set
temperatures.
In the event of an alarm, the acoustic alarm and indicator lights are activated. Important: to disable the acoustic
signal, press the Reset filter/alarm. If not deactivated by pressing the button, the acoustic alarm will switch off
automatically after 10 minutes.
The alarm black-out activates when a prolonged interruption of the power supply has caused an increase in
temperature in the freezer compartment. The freezer display will flash, showing the maximum temperature
reached in the compartment during the interruption and the acoustic signal will come on.
The door alarm symbol lights up and the acoustic alarm is activated when one or both doors of the refrigerator
and/or freezer have remained open. When the doors are left open for more than 2 minutes, the symbol flashes
and an acoustic signal sounds.
The activation of the acoustic signal and the appearance of letters on the display, indicates the problem with
the appliance. If this happens, call customer service. You will be asked to provide the letter code shown on the
display instead of the temperature.
symbol comes on and an acoustic alarm is
lights on.
5019 315 01020
D D D G GB GB F F F N N NL
GB
E E E P P P I I I G GR GR
D
S S S N N N DK DK FIN FIN FIN
P P CZ S SK S H
PL CZ CZ H H
RUS RU RU BG BG BG RO RO RO
appears on the left of
.