Cleaning And Maintenence; Environment; Trouble Shooting - MaxPro PROFESSIONAL MPBTS1800/254 Manual De Instrucciones

sawing of narrow workpieces. Assume that this process is extremely dangerous.
Take all the necessary safety measures and con
blade) using a synthe stead of by hand.
Crosswise sawing
1.Remove the fence and apply the cross-cut fence in the righthand carriage.
2.Adjust the height of the saw blade (see lengthwise sawing).
3.Press the workpiece against the cross-cut fence and keep at least 2,5 cm distance from the front of the
saw blade.
4.Switch on the engine and wait un aximum number of rev
5.Press the workpiece against the fence and the bench. Carefully push the wood through the saw blade.
Con un behind the saw blade. Then switch off the engine and keep this
has stopped completely before you remove the wood.
6.Never pull the wood back. If necessary, switch the engine off and keep the
has stopped completely.
Crosswise sawing with a v cal mitre
This method is pr cally the same, except that the saw blade is placed in the angle required.
Only place the cross-cut fence on the righthand side of the saw blade.Never saw too small pieces of
wood. Never use your hands to carry out difficult opera
Crosswise sawing with a horizontal mitr
With this method the cross-cut fence must be secured at the angle required. Keep the workpiece pressed
firmly against the cross-cut fence and the bench before you start cu

CLEANING AND MAINTENENCE

A en efore performing any work on the equipment, pull the power plug.
Cleaning
Keep the ven a
R
Keep the ven a ree from dust and dirt.
If the dirt does not come o
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plas
parts.
Lubrica
The machine requir ca
STORAGE
Thoroughly clean the whole machine and its accessories. Store it out of the reach of children, in a stable
and secure posi in a cool and dry place, avoid too high and too low temperatures. Protect it from
exposure to direct sunlight. Keep it in the dark, if possible. Don't keep it in plas
build-up.

ENVIRONMENT

• Do not dispose of electric tools, accessories and packaging together with household waste material
- in observance of European Dir ve 2002/96/EC on waste of electric and electronic equipment and its
implementa in accordance with na law, electric tools that have reached the end of their life must
be collected separately and returned to an environmentally compa
8
push the workpiece through (un behind the saw
reached.
un the saw blade
un the saw blade
ff.
to prevent overhea
referably a er each use.
stened with soapy water.
bags to avoid humidity
recycling facility
GB

TROUBLE SHOOTING

Fault Symptom Possible Cause
Out of service at switch- Shortcircuit in motor winding
on
Disc between plug and
power socket
Novoltage in supply socket
Wearout of carbon brush
Loose switching contact
Disc etween carbon brush
and commutator
E x c e s s i v e s p a r k l i n g Underpressure in carbon brush spring Replace carbon brush by reparier
during running
Excessive wearout of carbon brush
Overvoltage in supply power
Disc etween carbon brush
and commutator
Ring fire caused by shortcircuit in
rotor winding shortcircuit
Ring fire caused by shortcircuit in
commutator segment
Running speed drop Decline in supply voltage
Mechanical part damage
St at low speed
P tcircuit in rotor
Machine overhea Electromotor overload
Unsmooth air outlet
Cu Untrimmed sawnotch due to blunt
saw blade
Resin or sawdust on saw blade
Saw blade unmatched to raw material
to be sawed
Running speed drop
Excessive mechanical I m p ro p e r l y s e
vibra omi feet
Fastening screw in loosening
Saw blade distorted or damaged
Sawdust in splashing Blockup at sawdust bleed hole
during cu
Laser flashlight out of Running out of charging capacity in
service accumulator
At switch-off
loose switching contact
Laser flashlight damaged
Difficult to shut down saw Blockup at movable guard due to
blade movable guard sawdust or foreign material
Tr
Replace stator/rotor by repairer
Put plug in power socket
Check and repair supply power
Replace carbon brush by repairer
Replace switchboard by repairer
Check c between carbon
brush and commutator
Replace carbon brush by reparier
Regulate supply voltage
Replace carbon brush
Check or replace rotor by repairer
Check or replace rotor by repairer
Check and repair supply power
Replace mechanical part by repairer
Regulate to high speed
Check or replace rotor by repairer
Operate with reference to instruc
manual
Clear up air duct and air outlet
Replace saw blade by repairer
Remove foreign material
Replace saw blade by repairer
Check electric motor and supply
voltage
m a c h i n e o r Properly rese g machine or refix
rubber feet
Screw up fastening screw
Replace saw blade by repairer
Clear up sawdust bleed hole or keep it
connected with dust extractor
Replace laser flashlight accumulator
Switch on
replace switchboard by repairer
replace laser flashlight by repairer
Remove sawdust or foreign mateiral
GB
n
9