Página 1
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays) For all your newfangled gadgetry. Desk NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Steel River Collection | Model 427652 PLEASE READ AND KEEP FOR FUTURE REFERENCE. Sauder.com English pg 1-49 Français pg 50-54 Español pg 55-59...
Página 2
Table of Contents Assembly Tools Required Part Identification No. 2 Phillips Screwdriver Hardware Identification Tip Shown Actual Size Hardware Usage Guide Assembly Steps 7-45 Hammer Not actual size Français 46-50 Español 51-55 Safety 56-58 Warranty Page 2 www.sauder.com/service 427652...
RIGHT UPRIGHT (1) BB SMALL LEFT DRAWER SIDE (2) FRONT LARGE MOLDING (1) RIGHT END (1) CC SMALL RIGHT DRAWER SIDE (2) BACK LARGE SKIRT (1) RAIL SUPPORT (6) DD SMALL DRAWER BACK (2) LARGE DRAWER FRONT (1) 427652 www.sauder.com/service Page 3...
METAL BRACKET -20 2" PAN HEAD SCREW - 12 1-3/16" PAN HEAD SCREW - 14 1" FLAT HEAD SCREW - 12 1" MACHINE SCREW - 3 1/2" FLAT HEAD SCREW - 24 1/2" PAN HEAD SCREW - 66 Page 4 www.sauder.com/service 427652...
Página 5
The arrow in the HIDDEN CAM must point Arrow toward the hole in the edge of the board. Hidden Cam Hidden Cam Hole Insert the CAM SCREW or CAM DOWEL into the HIDDEN CAM. Tighten the HIDDEN CAM. 427652 www.sauder.com/service Page 5...
Página 6
Step 1 Look for this icon. It means a video assembly tip is available at www.sauder.com/service/tips Find the numbered video or scan the QR code. å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Página 7
Fasten the LEFT END (E) to the LEFT END FRAME (K). Use two 2" PAN HEAD SCREWS (14). 1/2" PAN HEAD SCREW (2 used in this step) 2" PAN HEAD SCREW (2 used in this step) 427652 www.sauder.com/service Page 7...
Página 8
å Fasten a RAIL SUPPORT (J) to the LEFT END (E). Use two 1" FLAT HEAD SCREWS (16). 1" FLAT HEAD SCREW (2 used in this step) This hole must be here. Surface with more holes Page 8 www.sauder.com/service 427652...
Página 9
Turn two CAM SCREWS (8) into the LEFT UPRIGHT (F). å Fasten four METAL BRACKETS (11) to the LEFT UPRIGHT (F) and LEFT UPRIGHT FRAME (L). Use four 1/2" PAN HEAD SCREWS (18). Arrow 1/2" PAN HEAD SCREW (4 used in this step) 427652 www.sauder.com/service Page 9...
Página 10
Fasten the LEFT UPRIGHT (F) to the LEFT UPRIGHT FRAME (L). Use two 2" PAN HEAD SCREWS (14). 2" PAN HEAD SCREW (2 used in this step) 1/2" PAN HEAD SCREW (2 used in this step) Page 10 www.sauder.com/service 427652...
Página 11
å Fasten the RAIL SUPPORT (J) to the LEFT UPRIGHT (F). Use two 1" FLAT HEAD SCREWS (16). 1" FLAT HEAD SCREW (2 used in this step) This hole must be here. Surface with more holes 427652 www.sauder.com/service Page 11...
Página 12
NOTE: The EXTENSION SLIDES will be used later for the DRAWERS. Push the black lever in and pull the SLIDE from the RAIL. Open end Open end 1/2" FLAT HEAD SCREW (4 used in this step) Open end Page 12 www.sauder.com/service 427652...
Página 13
Push four HIDDEN CAMS (7) into one of the SMALL BACKS (D). Just think. The sooner you do this, the sooner å Fasten the SMALL BACK (D) to the LEFT END (E). Tighten you do something else. two HIDDEN CAMS. Arrow Arrow 427652 www.sauder.com/service Page 13...
Página 14
Use two 1/2" PAN HEAD SCREWS (18) through the METAL (3 used in this step) BRACKETS and into the LEFT END FRAME. METAL BRACKET must be even with this edge. METAL BRACKET must be closer to this edge. Page 14 www.sauder.com/service 427652...
Página 15
Tighten two HIDDEN CAMS. å Fasten the LEFT UPRIGHT FRAME (L) to the SMALL SKIRTS (P) and FRONT MOLDING (Q). Use three 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (3 used in this step) 427652 www.sauder.com/service Page 15...
Página 16
Fasten one of BOTTOMS (C) to the LEFT END FRAME (K), LEFT UPRIGHT FRAME (L), and SMALL SKIRTS (P). Use six 1/2" PAN HEAD SCREWS (18) through the METAL BRACKETS and into the BOTTOM. 1/2" PAN HEAD SCREW (6 used in this step) Page 16 www.sauder.com/service 427652...
Página 17
Turn two CAM SCREWS (8) into the RIGHT UPRIGHT (G). å Fasten four METAL BRACKETS (11) to the RIGHT UPRIGHT (G). and RIGHT UPRIGHT FRAME (N). Use four 1/2" PAN HEAD SCREWS (18) Arrow 1/2" PAN HEAD SCREW (4 used in this step) 427652 www.sauder.com/service Page 17...
Página 18
Fasten the RIGHT UPRIGHT (G) to the RIGHT UPRIGHT FRAME (N). Use two 2" PAN HEAD SCREWS (14) 1/2" PAN HEAD SCREW (2 used in this step) 2" PAN HEAD SCREW (2 used in this step) Page 18 www.sauder.com/service 427652...
Página 19
å Fasten two RAIL SUPPORTS (J) to the RIGHT UPRIGHT (G). Use four 1" FLAT HEAD SCREWS (16). 1" FLAT HEAD SCREW (4 used in this step) This hole must be here. Surface with more holes 427652 www.sauder.com/service Page 19...
Página 20
Turn two CAM SCREWS (8) into the RIGHT END (H). å Fasten six METAL BRACKETS (11) to the RIGHT END (H) and RIGHT END FRAME (O). Use six 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (6 used in this step) Page 20 www.sauder.com/service 427652...
Página 21
Fasten the RIGHT END (H) to the RIGHT END FRAME (O). Use two 2" PAN HEAD SCREWS (14). 2" PAN HEAD SCREW (2 used in this step) 1/2" PAN HEAD SCREW (2 used in this step) 427652 www.sauder.com/service Page 21...
Página 22
Fasten the remaining RAIL SUPPORTS (J) to the RIGHT END (H). Use four 1" FLAT HEAD SCREWS (16). 1" FLAT HEAD SCREW (4 used in this step) Surface with more holes These holes must be here. Page 22 www.sauder.com/service 427652...
Página 23
Fasten the CABINET RAILS (3 and 4) to the RAIL SUPPORTS (J). Use eight 1/2" FLAT HEAD SCREWS (19) in the holes shown in the enlarged diagram. å NOTE: The CABINET RAILS are marked "L" and "R" for easy identification. Roller end Roller end Roller end 1/2" FLAT HEAD SCREW (8 used in this step) Roller end 427652 www.sauder.com/service Page 23...
Página 24
Step Step 19 å Push four HIDDEN CAMS (7) into the remaining SMALL BACK (D). å Fasten the SMALL BACK (D) to the RIGHT UPRIGHT (G). Tighten two HIDDEN CAMS. Roller end Arrow Arrow Page 24 www.sauder.com/service 427652...
Fasten the SMALL SKIRTS (P) to the RIGHT UPRIGHT FRAME (N). your drink. Use two 1/2" PAN HEAD SCREWS (18). METAL BRACKET must be even with this edge. 1/2" PAN HEAD SCREW (3 used in this step) METAL BRACKET must be closer to this edge. 427652 www.sauder.com/service Page 25...
Página 26
HIDDEN CAMS. å Fasten the RIGHT END FRAME (O) to the SMALL SKIRTS (P) and FRONT MOLDING (Q). Use three 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (3 used in this step) Roller end Page 26 www.sauder.com/service 427652...
Página 27
Step 22 å Fasten the BOTTOM (C) to the RIGHT UPRIGHT FRAME (N), RIGHT END FRAME (O), and SMALL SKIRT (P). Use six 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (6 used in this step) 427652 www.sauder.com/service Page 27...
Página 28
Stand the RIGHT UPRIGHT FRAME (N) assembly upright å Fasten the FRONT LARGE MOLDING (R) to the RIGHT UPRIGHT FRAME (N). Use two 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (2 used in this step) Page 28 www.sauder.com/service 427652...
Página 29
Step 24 å Fasten the BACK LARGE SKIRT (S) to the RIGHT UPRIGHT FRAME (N). Use two 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (2 used in this step) 427652 www.sauder.com/service Page 29...
Página 30
Fasten the LARGE BACK (B) to the RIGHT UPRIGHT FRAME (N). Use two 2" PAN HEAD SCREWS (14). 2" PAN HEAD SCREW (2 used in this step) Edge with holes. This hole should be closer to this edge. Page 30 www.sauder.com/service 427652...
Página 31
Fasten the LEFT UPRIGHT FRAME (L) to the FRONT LARGE MOLDING (R) and BACK LARGE SKIRT (S). Use four 1/2" PAN HEAD SCREWS (18). 1/2" PAN HEAD SCREW (4 used in this step) 2" PAN HEAD SCREW (2 used in this step) 427652 www.sauder.com/service Page 31...
Página 32
Step Step 27 å Turn four CAM SCREWS (8) into the TOP (A). Page 32 www.sauder.com/service 427652...
LARGE BACK. å Fasten the TOP (A) to the ENDS (E and H). Use six 1/2" PAN HEAD SCREW (18) through the METAL BRACKETS and into the TOP. 1/2" PAN HEAD SCREW (6 used in this step) 427652 www.sauder.com/service Page 33...
Página 34
Step 29 å Turn four CAM SCREWS (8) into the LARGE DRAWER FRONT (T). å Push four HIDDEN CAMS (7) into the LARGE DRAWER SIDES (U and V). Arrow Page 34 www.sauder.com/service 427652...
Slide a DRAWER BOTTOM (Y) into the grooves in the HEAD SCREWS (15). LARGE DRAWER SIDES (U and V) and LARGE å NOTE: Be sure the WOOD DOWELS in the RIGHT LARGE DRAWER BACK (X). DRAWER SIDE insert into the FILE GLIDE HOLDER. 427652 www.sauder.com/service Page 35...
DRAWER SIDES (U and V). Tighten four HIDDEN CAMS. å Fasten a KNOB and BACKPLATE (10) to the LARGE DRAWER FRONT (T). Use a 1" MACHINE SCREW (17). 1" MACHINE SCREW (1 used in this step) Page 36 www.sauder.com/service 427652...
HEAD SCREWS (19) through the holes shown in the enlarged diagram. å Push the FILE GLIDES (13) onto the LARGE DRAWER BACK (X) and FILE GLIDE HOLDER (Z). Open end 1/2" FLAT HEAD SCREW (4 used in this step) Open end Open end 427652 www.sauder.com/service Page 37...
Página 38
Step Step 33 å Turn eight CAM SCREWS (8) into the SMALL DRAWER FRONTS (AA). å Push eight HIDDEN CAMS (7) into the SMALL DRAWER SIDES (BB and CC). Arrow Page 38 www.sauder.com/service 427652...
Página 39
NOTE: Be sure the DRAWER BOTTOM (Y) inserts into the groove of the DRAWER FRONT (AA). å Fasten the KNOB and BACKPLATE (10) to the SMALL DRAWER FRONT (AA). Use a 1" MACHINE SCREW (17). å Repeat this step for the other small drawer. 427652 www.sauder.com/service Page 39...
Página 40
DRAWER LEFT (6) to the SMALL LEFT DRAWER SIDE (BB). Use four 1/2" FLAT HEAD SCREWS (19). å Repeat this step for the remaining drawer. 1/2" FLAT HEAD SCREW (8 used in this step) Roller end Roller end Page 40 www.sauder.com/service 427652...
Página 41
RAILS on the unit and push the drawer into the unit until the drawer is fully inserted. The drawer will push in hard until it is all the way in, then it will slide in and out easier. 427652 www.sauder.com/service Page 41...
Página 42
NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. And to celebrate, why not share your success story at sauder.com or (24 used) Page 42 www.sauder.com/service...
Modèle 427652 Bureau Utilisez les instructions d’ a ssemblage en français avec les NOUS CONTACTER EN PREMIER schémas étape par étape du manuel d’instruction en anglais. AVANT D'EFFECTUER TOUT RETOUR AU MAGASIN. Chaque étape en français correspond à la même étape en Nous faisons de notre mieux pour nous assurer que votre meuble anglais.
Página 44
Faire tourner deux VIS D’EXCENTRIQUE (8) dans le MONTANT GAUCHE (F). Fixer quatre CONSOLES EN MÉTAL (11) au MONTANT GAUCHE (F) et au CADRE DE MONTANT GAUCHE (L). Utiliser quatre VIS TÊTE GOUTTE DE SUIF 13 mm (18). Page 44 www.sauder.com/service 427652...
Página 45
Utiliser deux VIS TÊTE GOUTTE DE SUIF 13 mm (18) à travers les CONSOLES EN MÉTAL et dans le CADRE D'EXTRÉMITÉ DROIT. Fixer le MONTANT DROIT (G) au CADRE DE MONTANT DROIT (N). Utiliser deux VIS TÊTE GOUTTE DE SUIF 51 mm (14). 427652 www.sauder.com/service Page 45...
Página 46
Fixer le DESSUS (A) aux EXTRÉMITÉS (E et H). Utiliser six VIS DROIT (N). Utiliser deux VIS TÊTE GOUTTE DE SUIF 13 mm (18). TÊTE GOUTTE DE SUIF 13 mm (18) à travers les CONSOLES EN MÉTAL et dans le DESSUS. Page 46 www.sauder.com/service 427652...
Página 47
Décoller les APPLIQUÉS des FICHES D'APPLIQUÉS (12) et coller les sur chaque EXCENTRIQUE ESCAMOTABLE visible. REMARQUE : Prière de lire les informations importantes sur la sécurité figurant sur les pages arrière du manuel d’instructions. Ceci complète l'assemblage. Nettoyer avec un tissu humide. Essuyer. 427652 www.sauder.com/service Page 47...
PANEL SUPERIOR ............1 (JUEGO DE EXTENSIÓN SE MUESTRA POR su referencia futura. Si SEPARADO) necesita ponerse en DORSO GRANDE ............1 contacto con Sauder en RIEL DE EXTENSIÓN ..........2 FONDO ................2 cuanto a esta unidad, CORREDERA DE EXTENSIÓN ......2 DORSO PEQUEÑO ............2 refiérase al número...
Página 49
Gire dos BIELAS DE EXCÉNTRICO (8) en el PARAL IZQUIERDO (F). Fije cuatro SOPORTES DE METAL (11) al PARAL IZQUIERDO (F) y al MARCO DE PARAL IZQUIERDO (L). Utilice cuatro TORNILLOS DE CABEZA REDONDA de 13 mm (18). 427652 www.sauder.com/service Page 49...
Página 50
Gire dos BIELAS DE EXCÉNTRICO (8) en el PARAL DERECHO (G). Fije cuatro SOPORTES DE METAL (11) al PARAL DERECHO (G) y al MARCO DE PARAL DERECHO (N). Utilice cuatro TORNILLOS DE CABEZA REDONDA de 13 mm (18). Page 50 www.sauder.com/service 427652...
Página 51
Fije el PANEL SUPERIOR (A) a los EXTREMOS (E y H). Utilice seis DERECHO (N). Utilice dos TORNILLOS DE CABEZA REDONDA TORNILLOS DE CABEZA REDONDA de 13 mm (18) a través los de 13 mm (18). SOPORTES DE METAL y en el PANEL SUPERIOR. 427652 www.sauder.com/service Page 51...
Página 52
NOTA: Por favor, lea las páginas de atrás del folleto de instrucciones en cuanto a importante información de seguridad. CORRIMIENTO DE ARCHIVERO (Z). Esto completa el ensamblaje. Limpiar con un trapo húmedo. Seque con un paño. Page 52 www.sauder.com/service 427652...
Página 53
à Les téléviseurs peuvent être particulièrement un téléviseur. cet effet. lourds. De plus, le poids et l’emplacement du tube image ont tendance à rendre les téléviseurs instables et enclins à tomber vers l’ a vant. 427652 www.sauder.com/service Page 53...
Página 54
Además, el peso y la ubicación del tubo de imagen tienden a causar la inestabilidad de televisores y propensa a volcarse hacia adelante. Page 54 www.sauder.com/service 427652...
à compter de la date d'achat la première fois et qui sont signalés à Sauder dans les limites de couverture de la contre tout défaut de matériaux ou de fabrication des composantes de mobilier Sauder.
Página 56
BEFORE MAKING ANY RETURNS TO THE RETAILER. So, how did it go? Dear Valued Customer: Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built.