Additional Information - Dyson pure hot+cool HP04 Manual De Instrucciones

Additional information

CONTROL WITHOUT REMOTE
• The machine can be controlled through your Dyson Link app.
DYSON LINK APP CONNECTIVITY
• You must have a live Internet connection in order for the Dyson Link app to work.
• The machine can connect to either 2.4GHz or 5GHz networks which includes most
modern routers. Check your router documentation for compatibility.
• The Dyson Link app requires an iOS device with at least iOS version 10* or an Android
device with at least Android version 5.
• Your mobile device must have Bluetooth
wireless technology Low Energy) in order to set up a connection with the machine.
Check your device specification for compatibility.
– BLE/Wi-Fi 2.4GHz – 2.5GHz, 0.1W max
– Wi-Fi 5.170GHz – 5.835GHz, 0.1W max
Supported Wi-Fi protocols:
– IEEE802.11a
– IEEE802.11b (Not recommended)
– IEEE802.11g
– IEEE802.11n
REPLACEABLE PARTS
Your machine has replaceable filters and batteries, any other servicing must be carried out
by an authorized service representative.
BATTERY REPLACEMENT
CAUTION
• Unscrew the battery compartment on the remote control. Loosen the base and pull to
remove the battery.
• Do not install backwards or short circuit the batteries.
• Do not attempt to dismantle or charge the batteries. Keep away from fire.
• Follow battery manufacturers' instructions when installing new batteries (battery type
CR 2032).
20
wireless technology 4.0 support (Bluetooth
®
• Always replace the screw in the remote control and refer to the battery hazard in the
warning section.
• WARNING: Chemical Burn and Choking Hazard. Keep batteries away from children. This
product contains a lithium button/coin cell battery. If a new or used lithium button/coin
cell battery is swallowed or enters the body, it can cause severe internal burns and can
lead to death in as little as 2 hours. Always completely secure the battery compartment.
If the battery compartment does not close securely, stop using the product, remove
the batteries, and keep it away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate medical attention.
NON-WASHABLE FILTER UNITS
• Your filter units are non-washable and non-recyclable.
• To replace your filter units follow the steps as shown.
• Failure to replace the filter units when prompted may result in changes to product
performance and appearance.
• New filter units can be purchased at www.dyson.com/support.
AUTO MODE
• A period of 6 days is required after the machine is first used for the sensor to calibrate.
During this period, the machine may be more sensitive to VOCs (such as odors)
than normal.
®
• During first use, whilst the sensors calibrate, the machine can take up to 60 minutes to
show VOC and NO2 data.
AUTOMATIC CUT-OUT
• For your safety this machine is fitted with automatic cut-out switches that operate if the
machine tips over or overheats. If the switches operate, unplug the machine and allow
it to cool. Before restarting the machine check and clear any blockages and ensure the
machine is on a solid level surface.
• In heating mode the machine will automatically switch 'OFF' after 9 hours of continuous
use. To restart the machine, press the Standby ON/OFF button on either the remote
control or the base, or restart via the Dyson Link app.
DISPOSAL INFORMATION
• Dyson products are made from high grade recyclable materials. Recycle where possible.
• Dispose of or recycle the battery in accordance with local ordinances or regulations.
• Keep the used batteries away from children as these can still harm children if swallowed.
• Your filter units are non-washable and non-recyclable.
• Dispose of the exhausted filter units in accordance with local ordinances or regulations.
• The battery should be removed from the product before disposal.
• California: This product includes a separate remote control device with a coin cell battery.
The coin cell battery contains Perchlorates. Special handling may apply. See www.dtsc.
ca.gov/hazardouswaste/perchlorate