Publicidad
Idiomas disponibles
Idiomas disponibles
1
Operating instructions for KoiFeeder Solar
Periods out of use
If you do not use the solar feeder for an extended period of time, the switch (14) should be set to off („0") to prevent the battery from draining
Maintenance and care
Cleaning the housing
Only use water and a soft cloth. Be careful not to apply too much pressure to the housing, otherwise it may be destroyed. Clean the housing and particularly the cover (1) from time to time, or when dust or dirt has
accumulated, to maintain the full performance of the solar panel.
Repairs
If the housing or solar module are damaged, a repair is not possible. You may not continue using the affected part and it must be correctly disposed of.
Troubleshooting
Do not repair the solar feeder yourself! If you use unsuitable parts for the repair, the risk of an electrical short circuit can increase greatly. Some problems may be caused by minor faults that you can fix yourself. To
do this, follow the instructions below according to the problem in question.
If this does not solve the problem, please contact the customer service department and keep the required information at hand according to the item "Ordering spare parts".
Problem
The display is off
Display is on, but no feeding is taking place
Wheel is turning, but it does not eject feed
Ordering spare parts
When ordering spare parts, or in the course of troubleshooting according to the
item "Troubleshooting", we require the following information:
1. Article name
2. Article number of device
3. Copy of the invoice
4. Error description
2
Warranty
Our products are subject to stringent quality controls. However, we are very sorry if this device does fail to work properly. The following applies to the assertion of warranty claims:
1.
These warranty conditions are intended exclusively for consumers, i.e. natural persons who do not intend to use this product in the course of their commercial or other self-employed activities.
2.
Our warranty service covers the repair of material and manufacturing defects or the replacement of the device.
3.
Warranty claims are valid for a maximum of 2 years from the date of purchase. The assertion of warranty claims after the expiry of the warranty period is excluded.
4.
If the article is covered by the warranty, it will be repaired free of charge or replaced free of charge by an equivalent or similar article of our choice.
Repair or replacement of the device does not result in an extension of the warranty period, nor does this service initiate a new warranty period for the device or for any installed spare parts.
The following exclusions apply to our warranty:
-
Damage to the device caused by non-compliance with the operating instructions (such as the exchange of another accumulator), non-compliance with the maintenance and safety regulations or by
exposure of the device to abnormal environmental conditions or by lack of care.
-
Damage to the device caused by misuse or improper application (such as overloading the device or using non-approved application tools or accessories), penetration of foreign bodies into the device (such
as sand, stones or dust), use of force or external influences (such as damage due to dropping).
-
Damage to the device or parts of the device resulting from normal, customary or other natural wear and tear.
Information on the safe removal of the batteries or rechargeable batteries
1. Remove the 4 screws from the stands (15) and put them aside
2. Remove the 4 screws (12) from the lower part of the housing (10) where the sticker is located
3. Open the lower part of the housing (10)
4. Loosen the connection between the battery and the circuit board and remove the battery
5. The rechargeable battery and the device can now be disposed of separately
Cause
Battery drained
Main switch off
Connecting cable disconnected
Feed bucket empty
Wheel is jammed
Inlet blocked
Inlet blocked
Not enough feed in the bucket
Solution
Charge the battery by exposing the feeder to direct sunlight for about one hour.
Set the switch (14) to the "I" position
Loosen the screws (12), fix the connecting cables and re-tighten the screws.
Fill the feed bucket with suitable feed
Remove the screws from the stands (15) and the screws (12), remove the feed bucket (5), check the
wheel for blockages and remove foreign objects
Remove the feed and check that the feed is the right size.
Remove clumped feed
Remove clumped feed so that feed can continue to flow
Fill the feed bucket with a sufficient amount of feed
Technical data
Grain size of fish feed
Distribution angle
Tank size
Number of feeds per day
Charging time
Operating time
Protection class
Power supply not included in scope of the delivery
Range
Battery
Output
Dimensions
12
3 – 10 mm
120° horizontal
6 litres
1 – 6
Max. 30 hours
Up to max. 3 months with fully charged battery
IPX4
12 V / 1.66 A / DC connector 5.5x21
1 m (S); 2 m (M) 3 m (L)
Rechargeable lithium-ion
1,2 W
275 x 252 x 420 mm
Publicidad
