Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

MIXER SECTION:

CHANNEL INPUT SELECTOR: The CHANNEL INPUT SE-
23
LECTOR switches allow you to choose which input will be
controlled by that channels corresponding volume FADER.
For example CHANNEL (1) INPUT SELECTOR allows you to
choose between line (1) (That sides internal CD player), line
(2) which is line input RCA (1). The same applies for channel
2.
CHANNEL ROTARY GAIN: The CHANNEL ROTARY GAIN
24
allows you to boost the signal of each individual channel de-
pending on how low or high its input level is.
2-BAND EQUALIZER: The 2-BAND EQUALIZER adjusts the
25
tone of each CHANNEL by giving you a choice 2 frequencies
(BANDS) to adjust, from LOW and HIGH's, you can use the
adjustment knobs to raise or lower the 2 separate frequen-
cies until the sound of the music program is appropriate for
your listening environment.
CHANNEL VOLUME FADER: After you have chosen which
26
input you will use with the INPUT SELECTOR the corre-
sponding CHANNEL FADER will allow you to adjust the vol-
ume for that particular CHANNEL.
CHANNEL CUE SELECTOR: The CHANNEL CUE SELEC-
27
TOR allows you to choose which channel you wish to monitor
in your headphones, to the left is CHANNEL (1) to the right is
CHANNEL (2) and the middle position is BOTH (1 & 2).
CUE VOLUME ROTARY KNOB: The CUE VOLUME ROTA-
28
RY KNOB adjusts your HEADPHONE MONITOR OUTPUT'S
volume.
MICROPHONE VOLUME ROTARY KNOB: Allows you to ad-
29
just the volume of the microphone signal.
MASTER VOLUME ROTARY KNOB: The MASTER VOUME
30
rotary knob adjusts the volume of the MAIN MASTER out-
put.
VU METER: The CDM-3200 has a stereo VU METER that
31
allows you to monitor the decibel levels of the LEFT and
RIGHT MASTER output.
FADER START BUTTON: The Fader Start function allows
32
you to start CD playback simply by moving the CROSSFAD-
ER from side to side.
A. Cue up the CD player you wish to start using the Fader
Start function
B. Move the CROSSFADER all the way to the opposite
side of the CD you have just cued.
C. Press the FADER START SELECTOR button so that
the button becomes illuminated.
D. At the point in which you wish to start the audio from
the Cued CD, simply move the CROSSFADER in the di-
rection of the Cued CD player, and playback will begin.
E. When the CROSSFADER is moved all the way to the
6
opposite side of the currently playing disc, the unit will stop
playing that disc and return to the beginning of the track or
the set cue point.
CROSS FADER: The CROSS FADER allows you to mix
33
evenly from one source to another. The CROSS FADER on
the CDM-3200 is also removable and if the need arises can
be replaced. The RG-45 (RAILGLIDE™) DUAL-RAIL CROSS
FADER, which has internal dual stainless steel rails that allow
the slider to ride smoothly and accurately from end to end can
be purchased from your local GEMINI dealer.
NOTE: WHEN USING THE CROSS FADER LIGHTLY GLIDE
THE FADER BACK AND FORTH. PRESSING DOWN ON THE
CONTROLS CAN BEND CONTACTS AND CAUSE A LOSS
OF SOUND.
FADER REPLACEMENT:
1. UNSCREW THE FADER SCREWS. DO NOT TOUCH IN-
SIDE SCREWS CAREFULLY REMOVE OLD CROSS FADER
AND UNPLUG CABLE.
2. PLUG IN THE NEW CROSS FADER INTO CABLE AND
PLACE BACK INTO MIXER.
3. SCREW THE CROSS FADER TO MIXER WITH THE FAD-
ER PLATE SCREWS
4. REPLACE THE FACE OF THE MIXER AND SCREW THE
FOUR SCREWS BACK IN AND REPLACE THE FADER
KNOBS.
TROUBLESHOOTING:
- If a disc will not play, check to see if the disc was loaded cor-
rectly (label side up). Also check the disc for excessive dirt,
scratches, etc.
- If the disc turns but there is no sound, check the cable con-
nections, if they are ok, check your amplifier or receiver.
- If the CD skips, check the CD for dirt or scratches. Do not as-
sume that the CD layer is defective. Many CD's are recorded
out of spec and will skip on most or all CD players. Before
sending the unit for repair, try playing a CD that you are sure
plays properly.
CDM-3200

Publicidad

Tabla de contenido
loading

Tabla de contenido