Proteco MyGate myHook Manual De Uso E Instalación página 8

SAFETY CRITERIA
1 Attention: before beginning any kind of procedure of installation is absolutely
necessary to read all this manual.
2 Test/Control that the performances of the actuator answer to your installation
needs.
3 Besides control that:
• The gare hinges are in good conditions and perfectly fattened.
• The gate has mechanical stops in the opening and the closing.
INSTALLATION ADVICE
Connections:
• See the "Operational Diagram " and refer to the control central scheme.
• The electric cable in the exit from the actuator must be tight, but do an ample
curve towards the bottom in order to avoid the reflux in the inside of the
actuator itself. (Fig. Q)
• The adjustment must be effected when the device has no power supply.
• Foresee a omnipolar breaking device near to the apparatus (the contact must
measure at least 3 mm). Always protect the power supply using a 6A automatic
switch, or a 16A single-phase switch fises.
• The power supply lines the motors, to the control unit and the connection lines
to the outfits must be separated to avoid troubles which could generate
problems in the installation working.
• Any outfits (of control or safety) eventually connected to the control unit must
be tension free.
Spare parts:
• Use exclusively original spare parts.
• The batteries should be put with industrial waste and not with domestic refuse .
(Law n. 475/88).
Installation:
• In order to use correctly the product and to exclude the possibility of injury or
damage, refer to the "Generals" page enclosure, which is an integrated part of
this manual.
• The use of this equipment must be in observance of the safety standards in
force in the country where it is installed, as well as the standards governing
proper installation.
• Together with this manual is provided a label showing manufacturer's name and
product reference: please stick it insight on the equipment for future reference.
Warranty:
• The warranty supplied by the manufacturer becomes volid in the event of
interference, carelessness, improper use, lightening damage, power surges or
use by unqualified personnel.
• The warranty will also become in the following event: Failure to observe the
instructions given in the manuals supplied with the product.
The application of any part in a manner differing from that provided for current
legislation or the use of spare parts which are unsuitable and/or not approved
by manifacturer.
INSTALLATION INSTRUCTION SEQUENCE
1 Before the installation, analyze the risks referring to the chapter "Generalities"
of this instructions manual, fill the technic table and eliminate the risks noticed.
In case of more risks, foresee the installation with security system.
2 Test the security laws of the "Security Criteria".
3 Identify the right actuator and left actuator.
4 Control all the components.
5 Identify the fixing point on the gate and then on the pillar.
6 To lock the "Anchor plate" at the little pillar.
7 To lock the gear motor at the "Anchor plate".
8 To unclamp the actuator.
9 To put the articulated arm.
10 To lock the clamp S3 at the gate.
11 Stretch the wires as in the "Operational Diagram ".
12 Connect the central and all the accessories
13 Program the radio receptor
14 Program working times
In case of bad working, see the "Anomalies and advises".
If you do not find any solution call the nearest Assistence centre.
ELECTRO LOCK
Please notice that the electric lock must be installed on the swing that opens first
and must be connected with the terminal board of the control unit.
Position of the electric lock: (Fig. B)
Position 1: Lock between the wings
(in this case is necessary to use the bolt RT15 on the second wing).
Position 2: Lock in the floor
(in this case the utilization of the bolt is not necessary).
Remember to remove the lock or at least block the lock in opening position and take
away all the bolts of lock.
RIGHT OR LEFT ACTUATORS ACTUATORS (Fig. A)
The actuators are supplied in Right or Left version.
Right or left are established looking the gate from the side where the actuators are
installed, if the hinges are on the right the actuator is right, if they are on the left the
actuator is left.
Conseguently the actuator must be installed with the exit pin, positioned in the
hinges of the gates.
DETERMINATION OF FIXING MEASURES
To determinate the clamping point it is necessary pay attention to this:
• A = 300 mm (Fig. C)
Maximum dimension between the axis of the gate and the edge of the pillar.
• B = 30 mm (Fig. C)
Maximum dimension from the anchor plate to the edge of the pillar.
(to avoiod the possible brake of the edge)
• D = 14 mm (Fig. F)
Vertical distance from the clamping point of the clamp S3 on the gate, to the
anchor plate on the little edge.
Gate fixed in the middle of the pillar (Fig. D)
In this case the maximum al opening corner of the gate is 90°.
Gate fixed on the edge pillar (Fig. E)
In this case the gate can be opened with a corner greater than 90°.
Pay attention to this: growing the distance of the actuator from the edge of the pillar
measure B, the opening angle of the gate grows.
HEIGHT INSTALLATION (Fig. G)
Calculate the height of the actuator installation according to the gate's shape and
the fastening possibility.
a) If the gate has a big structure you can position it at any highness with no limits.
b) If the structure is light is necessary to put the operator as much as possible to
the centre of the gate (in heigth).
Position 1 Central beam of the gate
Position 2 Stiffen of the gate
FIXING THE ANCHOR PLATE
To dawel or to soldel the anchor plate on the little pillar near to the gate, paying
attention to the quotes indicate above.
In case of clamping with expanding loose pieces, use metallic loose pieces Ø13 mm
and consider that the loose piece has to be positioned at 30/35 mm distant from the
edge of the little pillar to avoid the possibility of broke.
In case of wolling pillar use chemical loose pieces, or resine loose pieces, or a
connectly wolled clamp.
It is possible to use the plate, in two different ways, for right or left actuator,
according to the particular exigences. (Fig. H / I)
MOTOR POSITION AND ARTICULATED ARM
1 Put the motor on the anchor plate, paying attention to the exit pin of the motor
must be turned to the interior of the gate.
2 Put together the three parts of the articulated arm. ( Fig. M)
The upright arm with the arm, and the arm with the clamp S3 with screws T.E.
12x35, self locking huts M12 and wasther Ø 12 mm.
3 To unclamp the motor using the normal key. (Fig. L)
4 Fit the articulated arm into the motor shaft (picture L) and fix it through the TE
bolt 8x16 and the Ø32 washer.
5 Extend the articulated arm till to positionate the fixing clamp S3 on the gate.
The best situation is given when the arm formes a little angle as showing in Fig.
C.
6 To solder up or to screw the clamp S3 to the gate.
LIMIT SWITCH REGULATION (fig. R)
1 Set the motor thrust
2 Give an opening impulse.
3 When the leaves reach the opening mechanichal limit switch it is necessary to
place the Cam of the micro limit switch and to fix it screwing it down without
forcing.
4 Give a closing impulse.
5 When the leaves reach the closing mechanichal limit switch it is necessary to put
the Cam of the limit switch and fix it by screwing it without forcing.
6 Regulate the motor thrust (as per the control unit instructions) It is possible to
Stop the working stroke of the gate with a force of 150N (about 15 Kg)
N.B. This kind of motor has been studied to be used with micro-limit swith.
If you do not use them unclamp the motor can be more difficult and you could
have a more rapid damage of the mechanical parts.
MECHANICAL STOP (Fig. A)
At this point you need to position the mechanical stop to proceed respectively, to
the wing's closing and opening stop.
EXTERNAL OPENING GATE.
If the gate opens till the exterior it is possible to put the actuator between the
two pilar.
Gate fixed in the middle of the pillar (Fig. N)
In this case the maximum al opening corner of the gate is 90°.
Gate fixed on the edge pillar (Fig. O)
Exterior fixed the pillar (Fig. P)
In this case the gate can be opened with a corner greater than 90°.
Pay attention to this: reducing the distance of the actuator from the edge of the
pillar measure A, the opening angle of the gate grows.
RELEASE OF THE ACTUATOR
- To keep out the cap on the fore part of the motor. (Fig. L)
- To put and to wheel of 90° in time sense the endowed key.
Not it is possible to open and to close the gate handly.
- To re-hook the actuator, to wheel in the contrary sense the endowed key.
It is not necessary the gate is in a particular position, because at the first order all the
volvers are restored.
ENGLISH