GLOBBER LEARNING BIKE Manual De Instrucciones página 5

Keep the instructions for future reference.
NF-EN-71
Warning! Protective equipment should be worn. Not to be used in
traffic.
Please carefully read the instructions before assembly and use
the toy.
Be careful when unpacking and assembling the product.
This toy must be assembled by a responsible adult.
Remove all the parts which are not necessary for play before
giving the toy to your child.
Warning! Do not step or stand on back of frame which will cause
product overturned.
Warning! Not to be used by children over 36 months. Insufficient
strength.
Warning! Make sure children's feet can touch the ground freely
before riding.
Do not use on wet days, or on wet ground.
How to assemble LEARNING BIKE:
(see page 4)
1. Pull the knob (grey colour) out and turn it 45 degrees to the right
until you hear a click.
2. Take out the black protector cap from the front wheels' head
tube, slot the body frame into the front wheels' head tube, then
turn the knob (grey colour) 45 degrees to the left to securely fix
the frame.
3. Unscrew the bottom hex screw located on the front of the
handlebars. Insert the handlebars' stem onto the front wheels'
head tube; push the handlebars' stem down and align the
handlebars' hex screw hole with the front wheels' head tube.
8
Make sure the handlebars are placed in the correct direction
[see pic 3] and re-tighten the screw with the Allen key included
in pack. Pull up the handlebars to make sure they are securely
fixed.
4. To install the rear wheels, unscrew the 2 screws on the rear
wheels' subassembly with the Allen key included in pack, then
insert the rear wheels' subassembly into the learning bike's
frame. Once it is in the correct position, with the holes of the
frame and the rear wheels' subassembly tube aligned, re-screw
the screws with the Allen key provided in pack and ensure that
they are securely tight.
5. To insert the saddle, open the clamp and press the bottom
spring-loaded button on the saddle's stem. Then, push the
saddle down until you hear a click. Close the clamp. The saddle
is adjustable with 2 available heights (24.2cm; 26.2cm). The
minimum saddle stem insertion level is noted by the 'IIIIIIIII
with MIN' marking on the saddle stem and corresponds to the
position of the spring-loaded in the upper tube hole.
How to operate the turning system: (see page 3)
- Hand-steering mode unlocked: Pull and turn the grey knob
45°to the right to activate the handlebar turning system from a
disabled position
- Hand-steering mode disabled: turn the grey knob 45° to the
left to disable the handlebar turning system from an unlocked
position.
- Lean-to-steering mode unlocked: pull the coloured button out
to activate the lean-to-steer function from a disabled position
- Lean-to-steering mode disabled: push the coloured button in
to lock the lean-to-steer function from an unlocked position.
The turning system comes with 4 modes of operation, thanks to its
the 2 locking systems:
- A) DIRECTION LOCKED MODE: The grey knob
needs to be disabled to lock the handlebar
turning system, and the coloured button also
needs to be disabled to lock the lean-to-steer
function. When in this position, the product can
only move in straight lines forward and
backward.
- B) CLASSIC HAND-STEERING MODE: The
grey knob needs to be enabled by pulling and
turning the knob 45° to the right to activate the
handlebar turning system. The coloured button
should remain disabled in this mode. When in
this position, the product can turn by moving the
handlebars by hand navigation.
- C) LEAN-TO-STEER MODE: The grey knob
needs to be disabled to lock the handlebar
turning system. The coloured button needs to be
enabled by pulling the coloured button out to
activate the lean-to-steer function. When in this
position, the product can turn by leaning into the
direction (left or right) your child wants to turn.
- D) LEAN-TO-STEER & HAND-STEERING
MODE: The grey knob needs to be enabled by
pulling and turning the knob 45° to the right to
activate the handlebar turning system.The
coloured button also needs to be enabled by
pulling the coloured button out to activate the
lean-to-steer function. When in this position, the product can be
used in both hand-steering and lean-to-steer to control the
steering & handlebar turning direction.
WARNING! Make sure the handlebar turning system (grey knob)
& the steering system are securely locked in the correct mode
before using the product.
General instructions of use:
- Prior to use, make sure that the product has been assembled
properly. Check all the connection elements; handlebar
must be correctly adjusted and make sure that the locking
mechanisms are securely locked. Check the product before the
child rides to determine if there are any potentially hazardous
parts or conditions.
- Children should be supervised by adult while riding this
product. Special care should be taken to instruct children in
safe riding.
- Do not use on the public highways, examples of safe riding
area: To be used on flat and no gravel areas (playground,
Public Square)
- Do not use this product near a staircase, on a slope, on a road
or on a wet surface.
- More mobility child grows; the more potential hazards increase.
At home, be sure to remove frames or mirrors hung too low
and could break, and any object that could fall in the event of
impact. Corner table can also be a danger.
- Do not allow more than one rider on the product at a time.
- Be sure the child wears clothes and appropriate footwear when
using product.
- Be sure the rider keeps both hands on the handlebars for
proper control.
- Do not allow the rider to wear anything that obstructs hearing
and visibility, or which impairs the functioning of product.
- The product should be used with caution since skill is required
9