Descargar Imprimir esta página

Hoover duros S3590 Manual Del Propietário página 9

Publicidad

Idiomas disponibles

Idiomas disponibles

Service
To obtain approved HOOVER service
and genuine HOOVER parts, locate
the nearest Hoover Factory Service
Center or Authorized Hoover Warranty
Service Dealer (Depot) by:
• checking the Yellow Pages under
"Vacuum Cleaners - Household" OR-
• checking the list of Factory Service
Centers provided with this cleaner
OR -
• checking the Service section of
Hoover, Inc. online at
www.hoover.com OR -
• calling 1-800-944-9200 for an auto-
mated referral of authorized service
outlet locations (U.S. only).
Please do not send your cleaner to
Hoover in Glenwillow for service, this will
only result in delay.
If further assistance is needed, contact
Hoover Consumer Response Center, Phone:
1-800-263-6376.
In Canada, contact Hoover Canada,
Carson Building, 100 Carson St.,
Etobicoke, Ontario M8W 3R9 Phone:
1-800-263-6376.
Always identify your cleaner by the com-
plete model number when requesting
information or ordering parts. (The model
number appears on the bottom of the
cleaner.)
Clearing blockages
Low suction or pick up may be due to
a blockage in the system. Refer to the
following steps to check for blockages,
continuing with each step until the block-
age is found:
1. Turn cleaner off and disconnect
from electrical outlet; then disconnect
power nozzle plug and wands from
hand grip.
All manuals and user guides at all-guides.com
4. If you have a
problem
If a minor problem occurs, it usually can
be solved quite easily when the cause is
found by using the check list below.
Problem: Cleaner won't run
Possible cause
Possible solution
• Not firmly plugged in.
• Plug unit in firmly.
• No voltage in wall plug.
• Check fuse or breaker.
• Blown fuse or tripped breaker.
• Replace fuse/reset breaker.
Problem: Cleaner suction low
Possible cause
Possible solution
• Filter bag full.
• Replace filter bag.
• Obstruction in nozzle connector,
hose or wands.
• Remove obstruction.
• Secondary filter dirty.
• Clean filter with water, allow to dry and
replace in cleaner.
• Power set too low.
• Increase power setting by pushing
suction control slide switch toward
MAX.
• Hose not properly connected to
cleaner
• Ensure hose is properly connected.
4-1
2. Plug cleaner in, turn on, and check
hose end for suction. Remove any
obstructions.
3. Remove power nozzle from wands
and attach wands to hose. Check for
suction and remove any blockages.
Problem: Agitator brush roll
won't run
Possible cause
Possible solution
• Broken or worn belt.
• Replace belt.
• RUG/FLOOR pedal set to "FLOOR".
• Set rug/floor pedal to "RUG".
• Power nozzle switch "OFF".
• Turn switch to "ON" position.
Problem: Nozzle won't pick up
Possible cause
Possible solution
• Low cleaner suction.
• See section "Cleaner suction low".
• Blockage in nozzle connector.
• Remove blockage.
• Agitator brush roll not running.
• See section "Agitator brush roll won't
run".
• Agitator brush roll brushes worn.
• Replace brushes.
4-2
A
4. Make sure power nozzle is discon-
nected from hand grip. Then check for
blockage in nozzle connector (A).
Push nozzle connector down to lowest
position. Look into nozzle connector and
remove any blockage.
Continued ➠
9

Publicidad

loading

Este manual también es adecuado para:

Duros s3592