Descargar Imprimir esta página

Whittier Wood Products 744Wa Instrucciones Para Armar

Torre para guardar videocasetes, cd, dvd y cintas

Publicidad

Enlaces rápidos

Model #
744Wa
Media Tower
Assembly Instructions
Two 744Wa Media Towers
shown with:
745W Home Theater Bridge
and 743W Home Theater Console
(Sold Separately)
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload shelves on this unit.
Before loading or moving this unit, check all screws
and supports for tightness.
For maximum stability, attach unit to the wall using
the enclosed hardware as per instructions.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • www.whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
We will replace any parts
Rev. 9/07

Publicidad

loading

Resumen de contenidos para Whittier Wood Products 744Wa

  • Página 1 Parts ship from our Eugene, Oregon factory Two 744Wa Media Towers shown with: within 1 or 2 business days from the time 745W Home Theater Bridge we receive the request.
  • Página 2 G — Face Frame — Qty. 1 Ca — Bottom Shelf — Qty. 1 H — Back — Qty. 1 I — Back Leg — Qty. 2 Da — Center Shelf — Qty. 1 Page 2 — 744Wa — Rev. 9/07...
  • Página 3 Head Screw — Qty. 4 ZG — Tipping Restraint Kit — Qty. 1 ZH — #6 x 1/2" Undercut Screw — Qty. 8 R — Hinge Plate — Qty. 2 Y — Handle — Qty. 1 Rev. 9/07 — 744Wa — Page 3...
  • Página 4 Side (Aa & Ba) Insert Rafix Bolts (L): two in Top Facing (F) ten in Face Frame (G) four in Top (Ea) FIG. 1B two in each Side (Aa & Ba) Page 4 — 744Wa — Rev. 9/07...
  • Página 5 The cam holes on the long edge must face the front. 4. Attach Right Side (Ba) to the Center Shelf (Da) and Bottom Shelf (Ca) in the same way. Rev. 9/07 — 744Wa — Page 5...
  • Página 6 Housings (P). FIG. 6 6. Attach the Top Facing (F) to the Top (Ea) with two Rafix Fittings (M). FIG. 7 7. Attach Top (Ea) to Sides (Aa & Ba) with Rafix Fittings (M). Page 6 — 744Wa — Rev. 9/07...
  • Página 7 DO NOT INSERT SCREWS SO DEEP THAT THE SCREW HEAD GOES BELOW THE SURFACE OF THE LEG! Insert a #8x1 " Black Screw (V) down through the predrilled hole in the bottom shelf into the leg. Repeat for the other Leg on the Right Side. Rev. 9/07 — 744Wa — Page 7...
  • Página 8 #7 x 1½" Type 17 Screw (X) into each punch to make the hole easier to see. Remove the screw and insert through the Spacer (S) and Hinge Plate (R). With the long arm facing out, fasten each set in place. Page 8 — 744Wa — Rev. 9/07...
  • Página 9 #6 x 1/2" Philtruss Screws (U) in the predrilled holes. Attach a Pad (ZC) to the front of the door stop. 15. Attach the Handle (Y) to the doors with #8 x 1" Machine Screws (Z). Rev. 9/07 — 744Wa — Page 9...
  • Página 10 The doors may need some adjusting after leveling the unit. 18. When you have determined the location for your unit, install the Furniture Tipping Restraint (ZG). Carefully follow the instructions contained on the package. Page 10 — 744Wa — Rev. 9/07...
  • Página 11 Dos 744Wa unidades se su nombre completo, dirección y teléfono, para el muestra con la 745W Estante del Sistema de caso de que necesitemos comunicarnos con usted.
  • Página 12 744Wa Torre para Guardar Videocasetes, CD, DVD y Cintas LISTA DE PIEZAS ANTES DE COMENZAR A ENSAMBLAR LA ESTANTERÍA: Verifi que que la cantidad de piezas recibidas concuerde con lo indicado en la lista que fi gura a continuación. Cantidad...
  • Página 13 Accesorio de Restricción El borde interior de ambos paneles laterales tiene que Evita que el Mueble se Volquee (ZG). Siga orifi cios troquelados para instalar las bisagras. cuidadosamente las instrucciones que vienen en el paquete. PG 3 – 744Wa SP...
  • Página 14 Deux 744Wa uniés illustrée avec la Les pièces sont expédiées de notre usine située à 745W Pont de Système Cinéma Eugene, Oregon dans les 1 ou 2 jours ouvrables Maison et 743W Console Système...
  • Página 15 (P) sur les connecteurs à came. Les trous de came situés sur le bord long doivent être face Introduisez chevilles 5 mm (N): à l’avant. deux dans chaque côté (Aa et Ba). PG 2 – 744Wa FR...
  • Página 16 (ZG). Veillez QUE LA PORTE S’OUVRE. Des trous préforés à suivre avec soin les instructions contenues dans sont ménagés dans le bord inférieur des deux côtés l’emballage. pour fi xer les charnières. PG 3 – 744Wa FR...