Tabla de contenido
Publicidad
Enlaces rápidos
Model #
743Wa
Home Theater
Console
Assembly Instructions
Shown with:
745W Home Theater Bridge
and two 744W Media Towers
(Sold Separately)
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb, sit or stand on this piece of
furniture.
Unload items from this unit prior to moving.
Do not overload shelves on this unit.
Before loading or moving this unit, check all screws
and supports for tightness.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
Outside U.S. or Canada: 541-687-0213
Fax: 541-687-2060 • www.whittierwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
We will replace any parts
Rev. 2/08
Publicidad
Tabla de contenido
Manuales relacionados para Whittier Wood Products 743Wa
Resumen de contenidos para Whittier Wood Products 743Wa
- Página 1 Model # 743Wa Home Theater Console Service Policy: We will replace any parts which are defective, missing or damaged Assembly Instructions during assembly. Please contact Whittier Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts.
- Página 2 743Wa Home Theater Console — Parts List BEFORE BEGINNING ASSEMBLY, check that the quantities of the parts received match those on parts list below. Wood trim — Garniture en bois — Acabado en madera Aa — Top — Qty. 1 B —...
- Página 3 743Wa Home Theater Console — Parts List (cont.) M — Door Glass — Qty. 2 Na — Adjustable Shelf — Qty. 2 O — #6x3/4" P.O. Screw — ZD — Plastic Insert — Qty. 2 W — Handle — Qty. 2 Qty.
-
Página 4: Tools Required
Side (Fa & Ga); the outer holes in each pair of holes near the the larger holes in the top and bottom edge bottom of each Side (Fa & Ga) of the Vertical Divider (Ea). Page 4 — 743Wa — Rev. 2/08... - Página 5 3. Attach the Left Side (Fa) to the bottom shelf assembly by gluing the dowels and fastening in place with Cam Connectors (ZK) and Cam Housings (ZG). Repeat with the Right Side (Ga). Rev. 2/08 — 743Wa — Page 5...
- Página 6 5. Hammer Tack Glides (ZE) into the bottom of the Back Legs (J). Thread the Adjustable Glides (ZC) on the Plastic Inserts (ZD) and tap into holes in the bottom of the Front Legs (H&I). Page 6 — 743Wa — Rev. 2/08...
- Página 7 Back (K) side to side and flush with the bottom shelf, with the cord cutout toward the top, and good side in. Fasten in place with #6x5/8" Philtruss Screws (P) through the predrilled holes. Rev. 2/08 — 743Wa — Page 7...
- Página 8 Cam Connectors in the base into the Bottom Shelf. Tighten the Rafix Cams through the holes in the bottom of the Cams. Insert the Cam Housings (ZG) over the Cam Connectors and tighten. Page 8 — 743Wa — Rev. 2/08...
- Página 9 Lay the glass retainer pieces flat on the glass and press the notched edge into the door frame along the glass. NOTE: Cutting the retainer at a 45° angle will give a more finished look. CAUTION: DO NOT LEAN ON GLASS WHEN WORKING ON THE DOOR. Rev. 2/08 — 743Wa — Page 9...
- Página 10 FIG. 14 FIG. 14A 14. To attach the doors to the unit, slide the Hinge arms onto the plates as shown in FIGURE 14. Follow directions in FIGURE 14A to adjust the doors. Page 10 — 743Wa — Rev. 2/08...
- Página 11 Attach Pads (T) to upper and lower corners of doors where they will make contact with the vertical divider. FIG. 16A FIG. 16 16. Install Adjustable Shelves (Na) using the Shelf Brackets (ZI) and #6x1/2" Undercut Screws (ZL) at desired locations. Rev. 2/08 — 743Wa — Page 11...
- Página 12 18. When you have determined the location for your unit, install the Furniture Tipping Restraint (ZM). Carefully follow the instructions contained on the package. Page 12 — 743Wa — Rev. 2/08...
-
Página 13: Consola Para Sistema De Teatro En Casa
Modelo # 743Wa Consola para Sistema Normas para obtener servicio: Reemplaza- de Teatro en Casa remos las piezas que tengan defectos, falten o se dañen durante el armado. Sírvase comunicarse con Instrucciones para Armar el departamento de servicio al cliente de Whittier Wood Products directamente (por teléfono, fax,... -
Página 14: 743Wa Consola Para Sistema De Teatro En Casa
743Wa Consola para Sistema de Teatro en Casa LISTA DE PIEZAS ANTES DE COMENZAR A ENSAMBLAR LA ESTANTERÍA: Verifique que la cantidad de piezas recibidas concuerde con lo indicado en la lista que figura a continuación. Cantidad Cantidad Cantidad Aa Panel superior ... 1 Tornillo de cabeza ZC Pata niveladora . - Página 15 NOTA: Si corta el retenedor a un ángulo de 45° le dará una apariencia mejor terminada. 743Wa SP (Rev. 2/08) – PG 3...
-
Página 16: Console De Système Cinéma Maison
No. de modèle 743Wa Console de Système Politique de service : Nous remplacerons toutes Cinéma Maison les pièces défectueuses, manquantes ou endom- magées pendant le montage. Veuillez contacter Instructions de Montage directement le service clientèle de Whittier Wood Products (par téléphone, fax, courrier ou e-mail) pour obtenir les pièces de remplacement. -
Página 17: 743Wa Console De Système Cinéma Maison
4. Insérez les boulons Rafix dans le dessus (Aa), par dessus à proximité du fond de chaque côté (Fa et Ga) les cames Rafix dans les côtés, puis collez les deux che- villes du séparateur vertical (Ea) dans le dessus. Serrez PG 2 – 743Wa FR (Rev. 2/08) - Página 18 (ZM). Veillez à suivre les mêmes que celles du verre des deux portes. Posez avec soin les instructions contenues dans l’emballage. ces morceaux à plat sur le verre, puis appuyez le bord à 743Wa FR (Rev. 2/08) – PG 3...