Descargar Imprimir esta página

Milwaukee 2678-20 Manual Del Operador página 5

Ocultar thumbs Ver también para 2678-20:

Publicidad

Idiomas disponibles

Idiomas disponibles

To avoid damage to the tool, do not
CAUTION
operate the tool without the retain-
ing pin fully inserted and locked into position.
Damage to the cylinder may occur.
An incomplete or faulty crimp could
WARNING
cause a fire. Jaws, dies, and con-
nectors must be used in an APPROVED COMBI-
NATION to achieve a successful operation. Im-
proper combinations can result in a faulty crimp.
Electric shock, fire, explosion, and property
damage could occur.
Changing the Dies
Inspect dies and connectors before use. Only use
properly matched dies and connectors for the ap-
propriate crimping jaws. Refer to Specifications for
die/connector/crimping jaws compatibility.
1. Remove the battery pack.
2. Push in the retaining pins and snap the appropriate
dies into each side of the crimping jaws. Release
the retaining pins.
3. To remove, push in the retaining pins pull dies out
from crimping jaws.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
Cutting Jaws (not included)
The Utility Crimper is compatible with the following
MILWAUKEE cutting jaws. Refer to the cutting jaws'
instructions for use.
Jaw Type
477 ACSR Jaws
(Cat. No. 49-16-2773)
750 MCM Cu Jaws
(Cat. No. 49-16-2772)
1/2" EHS
Guy Wire Jaws
(Cat. No. 49-16-2777)
Fine Stranded
Wire Jaws
(Cat. No. 49-16-2778)
* 750 MCM Cu Jaws will cut any aluminum cable with a
diameter less than 1.225"
** May require two cutting cycles to complete cut on 1/2" wire
*** Jaws should only be used on the following wire classes:
M, K, I/DLO
Maximum Capacity
ACSR: 477 MCM Hen ACSR
Guy Wire: 3/8" Non-EHS
Rebar: 3/8"
Ground Rod: 3/8"
Copper Cable: 750 MCM
Aluminum Cable:
1000 MCM *
EHS Guy Wire: 1/2"
(19 strand) **
Non-EHS Guy Wire: 1/2"
(7 & 19 strand) **
ACSR: 4/0 AWG
Rebar: 3/8"
Ground Rod: 3/8"
Fine Stranded Wire:
1/0 AWG - 777.7 AWG ***
OPERATION
To reduce the risk of arc flash,
WARNING
electric shock and property
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken first.
Keep hands away from crimping jaws while
tool is in use. Fingers could be crushed.
Always remove battery pack before changing
or removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Before crimping:
• Inspect the jaws and dies for cracks or other dam-
age. Do not use damaged jaws or dies. Contact a
MILWAUKEE service facility.
• Ensure retaining pin is properly seated and dies are
properly installed.
• Jaws, dies, connectors, and cables must be used
in an APPROVED COMBINATION. Improper
combinations can result in a faulty crimp.
• Inspect and discard workpieces with cracks or wear
before use. Materials may crack or shatter.
• Follow connector manufacturers' installation instruc-
tions. Other uses may cause damage to the tool,
accessories, and workpiece.
1. Insert battery pack.
2. Place jaws with installed dies around the connector.
3. Hold tool securely. Press and hold the trigger.
4. When the cycle is complete the tool will switch off
and the indicator will light. Release the trigger.
LED
Indicator
Definition
Solid Green Tool completed the operation and
reached full crimping pressure.
Tool completed the operation but did
Solid Red
NOT reach full crimping pressure.
Flashing Red Tool did NOT complete the operation.
Tool has reached its service interval
(40,000 crimps). Red/Green flashing
Flashing
will begin after the solid Red or Green
Red/Green
indicator for the operation is displayed.
(after Solid
MILWAUKEE recommends that the
Green or
tool be inspected and preventative
Solid Red)
maintenance completed. Return tool to
a MILWAUKEE service facility.
5. Continue crimping according to the connector
manufacturer's instructions. See the "Lug and
Splices" charts for more information.
• For splices, begin crimping in the center, work-
ing outward.
• For lugs, begin crimping near the pad, working
outward.
6. Two LEDs will light the workpiece when the trigger
is pulled.
5
Crimping

Publicidad

loading