EINHELL TP-BS 18/457 Li BL Manual De Instrucciones Original página 17

not supplied).
This will provide excellent dust extraction on the
workpiece.
Check that all the parts are properly connected.
Important. The vacuum cleaner you use for the
extraction work must be suitable for the workpie-
ce material.
5.1.2 Fitting the dust collection box
(Fig. 3/Item 7)
Slide the dust collection box (7) onto the connec-
tion for the dust extraction box (6). To remove the
dust collection box, proceed in reverse order.
The dust is transferred straight from the grinding/
sanding belt into the dust collection box.
To empty the dust collection box (7), open it with
the clip (a). The top part of the dust collection box
(7) can now be removed. Then clean the dust coll-
ection box (7) thoroughly and place the top part
back in position. As you do so, make sure that the
top part is fully inserted all around and that the
clip (a) is locked into position.
The dust collection box (7) can now be refi tted.
Important!
For health reasons it is imperative that you use
the dust collection box or a dust extraction system
via the dust extractor adapter!
5.2 Changing the grinding/sanding belt
(Fig. 4-5/Item 12)
•
Pull the clamping lever (9) outwards in order
to release the tension from the grinding/san-
ding belt.
•
Pull the worn grinding/sanding belt off the
drive rollers (11).
•
Push the new grinding/sanding belt onto the
drive rollers.
•
Make sure that the running direction of the
grinding/sanding belt (see arrow on the inside
of the grinding/sanding belt) is the same as
the running direction of the cordless belt grin-
der/sander.
•
Press the clamping lever (9) to the rear in or-
der to tension the grinding/sanding belt.
5.3 Adjusting the belt running position
(Fig. 6/Item 10)
•
Hold the cordless belt grinder/sander so that
the grinding/sanding plate is at the top.
•
Switch on the cordless belt grinder/sander.
•
Turn the setting screw (10) to adjust the
Anl_TP_BS_18_457_Li_BL_SPK13.indb 17 Anl_TP_BS_18_457_Li_BL_SPK13.indb 17
GB
belt running position such that the grinding/
sanding belt runs centrally on the two drive
rollers.
6. Starting up
6.1 Switching ON/OFF (Fig. 7)
To switch on:
Press the ON/OFF switch (5).
Continuous operation:
Secure the switch (5) with the locking button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
The machine can be operated on a temporary or
permanent setting.
6.2 Setting the belt speed (Fig. 8/Item 3)
You can select the belt speed by turning the set-
ting knob (3).
PLUS direction:
Increase belt speed
MINUS direction:
Reduce belt speed
6.3 Stationary use (Fig. 9-10)
You can use the cordless belt grinder/sander in
stationary mode.
To do so, use two screw clamps to fasten the
cordless belt grinder/sander on a strong and level
worktop or similar. The two fastening points (b)
must be used for this purpose.
6.4 Charging the Li battery pack (Fig. 1a-1b)
1. Remove the battery pack (c) from the handle,
pressing the pushlock button (d) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(e) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
- 17 -
14.11.2022 14:22:54 14.11.2022 14:22:54