Narex EPR 350-24 Instrucciones De Uso Originales página 20

English
1. Preface to the Operating Manual
This Operating Manual shall facilitate familiarization with the device and with its correct applications. The Operating Manual contains important in‑
structions how to handle the device safely, professionally and economically, thus avoiding risks, minimizing repairs and outage time and increasing
its reliability and service life. The Operating Manual must be available continuously on the place where the device is used. The Operating Manual
must be read and observed by all persons authorized to work with the machine, e.g. to operate, maintain or transport it. Besides the Operating
Manual and the mandatory regulations how to avoid injury, valid in the country where the device is used, it is also necessary to observe the generally
accepted technical rules for safe and professional work as well as the injury prevention rules of relevant professional associations.
Table of contents
1. Preface to the Operating Manual .............................................20
2 Safety warnings .........................................................................20
2.1 General Power Tool Safety Warnings .............................................20
3 Safety instructions for chain saws ............................................21
3.1 General chain saw safety warnings:...............................................21
3.2 Causes and operator prevention of kickback: ...............................21
4 Information about noise level and vibrations .........................21
5 Technical Specification ..............................................................22
6 Machine Description .................................................................22
7 Double insulation ......................................................................22
8. Use ..............................................................................................22
9 Putting into operation...............................................................22
9.1 Oil tank filling .....................................................................................22
9.2 Mounting of bar and chain ..............................................................23
9.3 Connection of the electric chainsaw ..............................................23
9.4 Power Plug ..........................................................................................23
9.5 Switching on ......................................................................................23
9.6 Electronic system ...............................................................................23
10. Safety devices on your electric chainsaw .................................24
10.1 Chain Brake ........................................................................................24
10.2 Runout brake ......................................................................................24
10.3 Chain catcher .....................................................................................24
11 Instructions for professional work
with the electric chainsawu ......................................................24
11.1 Tree felling ..........................................................................................24
12 Maintenance and service ..........................................................25
13 Technical problems ....................................................................25
14 Accessories .................................................................................25
15 Storage .......................................................................................26
16 Environmental protection .........................................................26
17 Warranty ....................................................................................26
18 Certificate of Conformity...........................................................26
2 Safety warnings
2.1 General Power Tool Safety Warnings
WARNING!
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference!
The term "power tool" in the warnings refers to your mains‑operated
(corded) power tool or battery‑operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug
in any way. Do not use any adapter plugs with earthed (ground-
ed) power tools. Unmodified plugs and matching outlets will re-
duce risk of electric shock.
20
Electric chain saw EPR 350-24, EPR 400-24
Original operating manual
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water en-
tering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or entangled cords in-
crease the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result
in serious personal injury.
b) Use personal protective equipment. Always wear eye protec-
tion. Protective equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate con-
ditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and prop-
erly used. Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preven-
tive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instruc-
tions to operate the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.