Morphy Richards Meno One Cup Manual De Instrucciones página 6

KT43923MEE Rev2 - MenoOneCup:9225 47507 MEE pump - Jon
g
OPERATING THE APPLIANCE
Before use
Before using your Meno One Cup for the first time or if you
have not used it for some time, rinse the machine by
running some water through the machine. Follow the
'Making a drink' instructions and dispose of the hot water.
Features
⁄ Water reservoir
¤ Reservoir filling point
‹ Handle
› Cup size selector
fi Stop button
fl Start button
‡ Spout
· Lights
‚ Drip tray
„ Base
‰ Power connector
 Boiling Chamber
Making a drink
1 To fill the water tank, lift the handle ‹ to the upright
position and carry to a tap to fill or by pouring water in
from a jug in position. The water tank flap will open
automatically when the handle is raised.
Once you have the required level of water and the unit is
back on the base „ securely, place the handle down. This
will close the flap.
2 Ensure that the drip tray is attached by sliding it into place.
‚
3 Adjust the cup size selector › to the correct size for your
cup, left being a small cup (150ml), right being a large cup
(maximum dispense at one time is 300ml). ›
4 Place a cup to hold the hot water on the drip tray below the
spout. ‡
5 Press the start button fl. The unit will become illuminated
and will begin to heat and dispense the required amount of
water.
6 If the unit does not start boiling, check the base is
connected correctly.
7 If you find the cup is getting too full, or you have not placed
your cup in position, the excess water will overflow into the
drip tray. Alternatively, press the stop button. fi
Ensure you empty the drip tray after every use when cooled
by removing from the bottom of the unit.
8 When dispensed, the illumination will go off and the unit
will make a gulping noise which is normal.
9 If you require another cup afterwards, ensure enough water
is in the tank, and press the start button again to begin.
6
15/2/10
If you want to empty the water from the unit, take off the
base and use the handle to carry to the sink and empty.
When you think it is empty, shake to ensure all the water
has been dispensed.
Descaling
IMPORTANT: As this appliance is fitted with a concealed
element it must be descaled regularly. The frequency of
descaling depends on usage and the hardness of the water
in your area.
Excessive scale can cause the appliance to switch off
before boiling and may damage the element invalidating the
warranty.
It is essential that regular descaling takes place.
1 Fill the water reservoir to maximum level with cold water.
2 Add one sachet of proprietary liquid descaler, which is
suitable for plastic kettles.
3 Set cup size selector › to maximum and place suitable
vessel under the spout.
4 Press the start button fl and allow the unit to run and
dispense the full volume of water.
5 Repeat steps 3 and 4.
6 Allow unit to stand for 10 minutes.
7 Press the start button fl and allow the unit to run and
dispense the full volume of water.
8 Repeat step 7 until the tank is empty.
9 Tip unit upside down over a sink and shake to remove any
water left in the boiling chamber Â.
10 Fill the water reservoir to maximum level with cold water.
11 Set cup size selector to maximum and place suitable vessel
under the spout.
12 Repeat steps 7-10.
13 Continue to use as normal.
IMPORTANT: Ensure that the electrical connections are
completely dry before using the appliance.
HINTS AND TIPS
Cleaning and maintenance
WARNING: Always disconnect the plug from the mains and
allow the appliance to cool before cleaning.
Wipe the outside with a damp cloth.
IMPORTANT: Do not use abrasive cleaners on the outside of
the appliance which may scratch the surface.
17:02 Page 6