Hudora 10700 Instrucciones Montaje Y De Uso página 4

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING YOUR PRODUCT!
Please read these instructions carefully. The instructions are an integral
component of the product. Therefore, please store them and the packaging
carefully in case questions arise in the future. Please always include these
instructions when handing on the product to a third party. This product is not
designed for industrial use. Use the product for its intended purpose only.
This product contains small parts which could cause asphyxia if swallowed.
Supervise children when they are assembling it, or have it assembled by an
adult. Children should only assemble or use the product when they are under
adult supervision.
TECHNICAL SPECIFICATIONS
Item:
Item number:
Handlebar height adjustable:
Saddle height adjustable:
Weight:
Maximum user weight:
CONTENTS
1 x Manual
1 x Bag including clamp, washers, guide sleeves, covers and tools
1 x Saddle with seat post
1 x Frame with rear wheel
1 x Handlebars with protective padding
1 x Front wheel fork
1 x Front wheel with nuts and axle lock washers
wARNING NOTICES
This product is only suitable for smooth paved surfaces. Do not use it on public
roads. The running bike is only intended for use by one person. Warning! Please
ensure that your child wears the appropriate protective clothing (helmet). The
running bike is not equipped with a breaking system since feet provide the
motion power to the driving wheels. Therefore, it is necessary to wear shoes
while using the bike. There is a risk of injury. Do not allow your child to ride the
running bike at twilight, at night or in poor visibility. To prevent putting your child
or others in danger, you should not let the running bike be used on roads or
thoroughfares or on slopes or hills. Avoid using it in the proximity of stairs or open
water. Inspect the running bike before each use to ensure that all parts are still
fixed in place correctly and that the running bike is functioning as intended. Keep
the instruction sheet. The product has been tested in accordance with standard
EN 71. For children from 2 to 5 years of age only.
ATTACHING THE wHEELS AND SADDLE
1. The rear wheel (1) is pre-mounted. Only the front wheel (2) has to be moun-
ted. Insert the front wheel (2) into the front wheel fork by removing the axle
lock washers (3) and external nuts (4) from the wheel axle. Check whether the
tapers (screw fittings on the wheel bearings) (5) are tightly screwed on to the
axles and secure them through the nuts (4). Now secure the wheel with the
aid of the hooks to the axle lock washers (3) in order to hook these into the
holes on the fork. Tighten the nuts (4) to the.
2. Attach the saddle (6) as shown in the picture. The cover (7) should initially
be pulled over the seat's supporting tube. Please take care not to exceed the
maximum seat height by refraining from pulling the saddle support higher
than the "MAX" indication as exceeding the maximum saddle height could
lead to serious injuries.
All manuals and user guides at all-guides.com
Running bike Seven
10700
52 – 60 cm
33 – 43,5 cm
3.65 kg
35 kg
HUDORA | Jägerwald 13 | 42897 Remscheid | Germany
ATTACHING THE HANDLEBARS
Attach the steering rod (8) parallel to the front wheel. The cover (7), the clamp
(9) and the two plastic washers (10) have to be pulled over the front wheel fork
and the steering rod supporting tube as shown in the illustration. Insert the guide
sleeves (11) into the stem of the frame as shown in the picture. The vertical
supporting rod has to be stuck into the upper end of the fork (with spreader). The
clamp (9) must be completely attached to the front wheel fork and not directly to
the vertical support. In order to set the highest position of the steering rod, the
vertical supporting tube can be pulled out to the "MAX" indication. Do not pull out
the rod further as this might lead to accidents. Then attach the clamp (9) securely
with the washer and nut. Please ensure that the steering rod is positioned cor-
rectly in relation to the front wheel before tightening the screw.
CARE AND MAINTENANCE
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and
after each use. Store the product in a safe place where it is protected from the
elements, cannot be damaged, and cannot injure anyone. For your own safety,
please use original spare parts only. These can be sourced from HUDORA. Do
not make any structural changes. If parts become damaged or if sharp edges or
corners should develop, the product may not be used any more. If in any doubt,
please contact our service team (http://www.hudora.de/).
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection
point provided in your area. Local waste management companies will be able to
answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous
information on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/artnr/10700/.
www.hudora.de
Art.-Nr. 10700
Stand 11/10
Seite 4/8