Chicco BebeCare Seat Up Manual De Instrucciones página 32

Then remove the Top Tether from the rear cov-
er (S) (Fig. 16).
Position the child car seat on the seat making
reference to the options suggested in your
car's user manual.
Fasten the two ISOFIX connectors (P) to the
corresponding ISOFIX hooks on the car seat
between the backrest and the seat (Fig. 17).
WARNING! Pull the car seat towards you and
then check that the two indicators are green
(Fig. 18) to make sure that the seat has been
installed correctly.
WARNING! Make sure there are no objects
between the child car seat and the vehicle
seat or between the child car seat and car
door.
Push the child car seat firmly against the back-
rest of the car seat (Fig. 19) to make sure it is
securely in place.
The assembly of the child car seat is complet-
ed exclusively with the installation of the Top
Tether (T).
WARNING! Refer to your car's user manual to
identify where the Top Tether of the child car
sear is attached to the car. This fastening point
is denoted with a specific label (Fig. 20) and
can be found in the positions indicated by the
figures 21A – 21B – 21C – 21D.
WARNING! Check that the Top Tether fasten-
er used is the one that has been specially des-
ignated. Do not confuse it with a ring used for
hanging bags (Fig. 22).
WARNING! Pass the Top Tether between the top
of the car seat backrest and the headrest. Never
pass the Top Tether above the car headrest.
Extend the Top Tether belt by pressing adjust-
ment button (V).
Once you have identified the fastening point,
connect to the Top Tether hook (U).
Adjust the length of the Top Tether belt by
forcefully pulling the belt until it is tight. The
indicator on the belt goes green (W) when
the tether is suitably tight (Fig. 23). Roll up any
excess belt and tie up using the velcro.
WARNING! In case of use in vehicles equipped
with rear seat belts with integrated airbags (in-
flatable belts), the interaction of the inflatable
portion of the vehicle's belt with this child re-
straint can result in serious injury or death! Do
not install this child restraint using an inflatable
seat belt. Install using ISOFIX instead, or move
the car seat to a position with a suitable seat
belt type. When installing with ISOFIX, the unu-
sed seat belt should not be buckled behind the
Child Restraint System as this will engage the
inflatable portion of the belt.
To disassemble the child car seat, unhook the
Top Tether and the Isofix connectors by press-
ing the release buttons (Q) (Fig. 24). To put
them back in completely push them inwards.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
6. HOW TO FIT THE GROUP 1 (9-18 kg)
CHILD CAR SEAT TO THE CAR WITH A
3-POINT SEAT BELT
WARNING! Never fit the seat belt in any way
not mentioned in this manual.
The slots for the car seat belts are clearly
marked on the child car seat with red colour
guide items.
Position the child car seat on the selected seat.
WARNING! Make sure there are no objects
between the child car seat and the vehicle
seat or between the child car seat and car
door.
Pull the car seat belt, and slide it through the
space between the backrest and the base of
the child car seat (Fig. 25).
Pass the abdominal part of the car's 3-point
seat belt through the specific red abdominal
belt guides (M). Pull it out from the other side
of the child car seat and fasten it to the buckle
of the seat until you hear a "CLICK" (Fig. 26).
Continue to assemble on the side of the re-
tractable part of the belt. Completely insert
the belt in the red clamp (L), holding it open
(Fig. 27).
After completing the assembly it is necessary
to make the safety harness as tight as possible.
Pull the diagonal part hard towards the retrac-
tor and fasten with the red clamp (L) (Fig. 28).
WARNING! Check that the child car seat is fit-
32