General Power Tool Safety Warnings; Electrical Safety - Makita DFT022F Manual De Instrucciones

ENGLISH (Original instructions)
SPECIFICATIONS
Model
Fastening torque
No load speed (RPM)
Dimensions
Net weight
Rated voltage
Battery cartridge
• Due to our continuing program of research and development, the specifications herein are subject to change with-
out notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

General Power Tool Safety Warnings

WARNING Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet con-
ditions. Water entering a power tool will increase
the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
DFT022F
Hard joint 0.5 - 2 N·m
(4 - 18 in·lbs)
Soft joint 0.5 - 2 N·m
(4 - 18 in·lbs)
700 /min
200 x 74 x 250 mm (7-7/8" x 2-15/16" x 9-7/8") (with Battery Cartridge BL1430B)
200 x 74 x 235 mm (7-7/8" x 2-15/16" x 9-1/4") (with Battery Cartridge BL1415NA)
DFT044F
1 - 4 N·m
(8.9 - 35 in·lbs)
1 - 4 N·m
(8.9 - 35 in·lbs)
950 /min
1.5 kg (3.4 lbs) (with Battery Cartridge BL1430B)
1.4 kg (3.0 lbs) (with Battery Cartridge BL1415NA)
D.C. 14.4 V
BL1415NA / BL1430 / BL1430B / BL1460A
8. When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit inter-
rupter (GFCI) protected supply. Use of an GFCI
reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication. A moment of inattention while operating
power tools may result in serious personal injury.
11. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
16. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
2 ENGLISH
DFT084F DFT126F
3 - 8 N·m 5 - 12 N·m
(27 - 71 in·lbs) (44 - 106 in·lbs)
3 - 8 N·m 5 - 12 N·m
(27 - 71 in·lbs) (44 - 106 in·lbs)
780 /min 410 /min