Publicidad
Idiomas disponibles
Idiomas disponibles
e) The table saw must be secured. A table
saw that is not properly secured may move or
tip over.
f)
Remove tools, wood scraps, etc. from the
table before the table saw is turned on.
Distraction or a potential jam can be dange-
rous.
g) Always use saw blades with correct size
and shape (diamond versus round) of
arbor holes. Saw blades that do not match
the mounting hardware of the saw will run off -
centre, causing loss of control.
h) Never use damaged or incorrect saw
blade mounting means such as fl anges,
saw blade washers, bolts or nuts. These
mounting means were specially designed
for your saw, for safe operation and optimum
performance.
i)
Never stand on the table saw, do not use
it as a stepping stool. Serious injury could
occur if the tool is tipped or if the cutting tool
is accidentally contacted.
j)
Make sure that the saw blade is installed
to rotate in the proper direction. Do not
use grinding wheels, wire brushes, or
abrasive wheels on a table saw. Improper
saw blade installation or use of accessories
not recommended may cause serious injury.
5) Additional safety information
1. Only use a saw blade which has the external
diameter and hole diameter specifi ed in the
original operating instructions ("Technical
data" section).
2. Use only blades with rotating speeds which
are equal to or higher than the rotating speed
marked on the power tool.
3. Use only a saw blade with a diameter which
is the same as specifi ed on the saw.
4. Use the correct saw blade for the material you
are working on.
5. Use only saw blades which are recommen-
ded by the manufacturer which, if they are
intended for cutting wood or similar materials,
comply with EN 847-1.
6. Only fi t blades which are well sharpened and
have no cracks or deformations.
7. Faulty saw blades must be replaced immedi-
ately.
8. It must be possible for the blade to run freely.
9. Check the saw blade guard for damage and
wear each time before using the saw.
10. The saw blade guard must lower again auto-
matically under its own weight after each cut.
The saw blade guard must lift when the work-
Anl_TE_TS_36_210_Li_USA_SPK7.indb 17
Anl_TE_TS_36_210_Li_USA_SPK7.indb 17
EN
piece is pushed in the direction of the saw
blade.
11. Damaged or faulty safety devices have to be
replaced immediately.
12. It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
13. Never dismantle the machine's safety devices
or render them inoperative.
14. Refi t all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
15. Keep the push stick or handle for a push
block at the machine at all times, even when
you are not using them. Slot the push stick or
the push block into its holder when not in use.
16. The sawing of angles/wedges is only per-
mitted if an appropriate auxiliary stop (cross
stop) is used.
17. If the table insert is worn, replace it. – Pull out
the battery.
18. If necessary, wear suitable personal protec-
tion equipment. This could consist of:
a. Ear plugs to prevent the risk of damaging
your hearing.
b. A breathing mask to avoid the risk of inha-
ling hazardous dust.
c. Always wear gloves when handling saw
blades and rough materials. Whenever
practicable, saw blades must be carried in a
container.
19. Use only the transport devices to move the
equipment. Never use the guards for handling
or moving the equipment.
20. While you are moving the machine it is best
to cover the top part of the blade, e.g. with the
guard.
21. Give these safety instructions to all persons
who work on the machine.
22. Do not use this saw to cut fi re wood.
23. Do not use this saw to cross-cut round wood.
24. The machine is equipped with a safety switch
to prevent it from being switched on again
accidentally after a power failure.
25. Never load the machine so much that it cuts
out.
26. Always press the workpiece fi rmly against the
saw table.
27. Make sure that off -cuts do not catch on the
saw blade crown. Risk of catapulting!
28. Be sure to observe the safety information
and operating and maintenance instructions
issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
29. It is imperative to observe the accident pre-
- 17 -
07.10.2022 09:39:58
07.10.2022 09:39:58
Publicidad
